1. Product Overview
This manual provides detailed instructions for the installation, operation, and maintenance of your CO-Z FYXES-SGO-RA 280W Sliding Gate Opener. This system is designed to automate sliding gates up to 600 kg (1322 lbs) in weight and 12 meters (40 ft) in length, offering convenience and security for residential and commercial applications. Please read this manual thoroughly before installation and use to ensure safe and correct operation.
2. Safety Information
Important Safety Instructions: Always follow these safety guidelines to prevent injury or damage.
- Ensure all electrical connections comply with local codes and regulations.
- Keep the area around the gate clear of obstructions during operation.
- Do not allow children to play near the gate or operate the remote controls.
- The system includes infrared sensors for obstacle detection. If an obstacle is detected, the gate will stop and reverse. Regularly check these sensors for proper function and clear any debris.
- The motor features overheat protection. If the motor overheats, it will temporarily cease operation until it cools down.
- In case of power failure, use the manual release keys to operate the gate manually.
- Perform regular inspections and maintenance as described in this manual.
Image: Overview of the safety features integrated into the CO-Z sliding gate opener system.
3. Package Contents
Verify that all components listed below are present in your package.
Image: Visual representation of all items included in the CO-Z sliding gate opener package.
- 1 x Control plate and motor
- 2 x Manual release keys
- 2 x Remote Controls
- 1 x Mounting plate
- 12 x Nylon Zipper (0.35 m each)
- 2 x Limit switches with accessories
- 4 x M8 foundation bolts
- 4 x M6 × 18 mounting bolts
- 4 x M8 × 40 Hex Bolts
- 24 x Self-tapping screws
- 24 x Mounting ear studs
- 8 x M8 Flat Washers
- 8 x M8 Elastic Washers (Spring Washers)
- 8 x M8 Nuts
- 2 x Infrared sensors
- 1 x User Manual
Note: Nylon zipper racks cannot be used together with steel zipper racks.
4. Specifications
| Rated Power | 280 W (0.37 hp) |
| Torque | 16 N·m |
| Max. Gate Weight | 600 kg (1322 lbs) |
| Max. Gate Speed | 13 m/min (42.5 ft/min) |
| Max. Gate Width | 12.2 m (40 ft) |
| Max. Remote Controls | 40 |
| Max. Noise Level | 56 dB |
| Operating Temperature | -20 to 70°C (-4 to 158°F) |
| Weatherproof Rating | IP44 |
| Remote Range | 30 m (98.4 ft) |
| Remote Frequency | 433.92 MHz |
| Motor Speed | 1400 r/min |
| Machine Speed | 56 r/min |
| Dimensions (L x W x H) | 25 x 22.5 x 26 cm (9.9 x 9 x 10.2 inches) |
| Item Weight | 35.2 pounds |
| Model Number | FYXES-SGO-RA |
Image: Key specifications of the CO-Z sliding gate opener.
Image: Dimensions of the gate opener components.
5. Installation and Setup
The CO-Z sliding gate opener is designed for straightforward installation. Ensure you have all components listed in Section 3 before beginning.
5.1 Site Preparation
- Ensure the gate slides smoothly and freely without obstruction.
- Clear the area where the motor will be mounted, ensuring a stable and level surface.
- Plan the routing for electrical wiring and sensor cables.
5.2 Mounting the Motor
- Position the mounting plate on the prepared surface next to the gate. Ensure it is level and at the correct height for the gate's rack.
- Mark the positions for the M8 foundation bolts.
- Drill holes and secure the mounting plate using the M8 foundation bolts, flat washers, elastic washers, and nuts.
- Attach the motor unit to the mounting plate using the M6 x 18 mounting bolts.
5.3 Installing the Nylon Racks
- Attach the nylon zipper racks to the bottom frame of your sliding gate.
- Ensure the racks are aligned with the motor's sprocket and maintain a small clearance (approx. 1-2mm) between the rack and the sprocket to allow for gate movement.
- Use the self-tapping screws and mounting ear studs to secure the racks firmly along the entire length of the gate.
- Verify that the gate moves smoothly across the entire travel path without binding or excessive friction with the sprocket.
5.4 Installing Infrared Sensors
- Mount the two infrared sensors on opposite sides of the gate opening, ensuring they face each other directly.
- Position them at a height where they can detect potential obstructions (e.g., vehicles, pedestrians).
- Connect the sensors to the control board according to the wiring diagram provided in the full user manual.
- Test the sensors to ensure they correctly detect obstructions and trigger the gate to stop and reverse.
5.5 Electrical Connection
- Connect the main power supply to the control board. Ensure the power supply matches the motor's requirements.
- All electrical work should be performed by a qualified electrician if you are unsure.
- Refer to the detailed wiring diagram in the complete user manual for specific connections.
Image: Example of a properly installed gate opener and gate.
6. Operating Instructions
Once installed, the CO-Z sliding gate opener offers various operating modes and features for convenient access control.
6.1 Remote Control Operation
- The system supports up to 40 remote controls. Two remote controls are included.
- To open or close the gate, press the designated button on the remote control. The remote range is up to 30 meters (98.4 ft).
- Refer to the full user manual for instructions on programming additional remote controls.
6.2 Pedestrian Mode
The pedestrian mode allows the gate to open partially, providing enough space for foot traffic without fully opening the gate. This feature enhances convenience and reduces wear on the motor. Consult the full user manual for activation and adjustment of pedestrian mode settings.
6.3 Auto-Close Function
The gate opener can be configured to automatically close after a set period. This system offers 3 self-closing presets (e.g., 12, 24, 36 seconds or 15, 30, 45 seconds depending on model configuration). Refer to the control board settings in the full user manual to enable and adjust the auto-close timer.
6.4 Manual Release
In the event of a power outage or system malfunction, the gate can be operated manually using the provided manual release keys. Insert the key into the lock on the motor unit and turn it to disengage the motor, allowing the gate to be pushed open or closed by hand.
Image: Smart features and operational modes of the gate opener.
7. Maintenance
Regular maintenance ensures the longevity and reliable operation of your CO-Z sliding gate opener.
- Monthly: Inspect the gate's movement. Ensure it slides freely without excessive friction. Clean the nylon racks and the motor's sprocket to remove any dirt, leaves, or debris.
- Quarterly: Check all mounting bolts and screws for tightness. Verify that the infrared sensors are clean and properly aligned. Test the obstacle detection feature by placing an object in the gate's path.
- Annually: Inspect electrical wiring for any signs of wear or damage. Lubricate any moving parts of the gate (hinges, rollers) as recommended by the gate manufacturer.
- Keep the motor housing clean and free from dust and moisture. The IP44 rating provides protection against splashes, but direct water jets should be avoided.
8. Troubleshooting
This section addresses common issues you might encounter. For more complex problems, contact customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Gate does not respond to remote control. |
|
|
| Gate stops or reverses unexpectedly. |
|
|
| Gate operates slowly or with difficulty. |
|
|
9. Warranty and Support
For warranty information, please refer to the documentation included with your purchase or contact CO-Z customer support directly.
If you encounter issues not covered in this manual or require further assistance, please contact CO-Z customer service. Provide your model number (FYXES-SGO-RA) and a detailed description of the problem for efficient support.
You can often find additional support and contact information on the official CO-Z website or through your retailer.