UPPARTS Passenger Side Tail Light Assembly Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your UPPARTS Passenger Side Tail Light Assembly. Please read this manual thoroughly before beginning installation to ensure proper fitment and functionality. This product is designed as a direct replacement for the original equipment manufacturer (OEM) tail light on specified Nissan NV models.

2. Safety Information

Always prioritize safety when working on your vehicle. Failure to follow safety guidelines may result in injury or damage to the vehicle.

• Ensure the vehicle is parked on a level surface with the parking brake engaged.
• Turn off the vehicle's ignition and remove the key.
• For electrical work, it is recommended to disconnect the negative terminal of the vehicle's battery to prevent electrical shorts.
• Wear appropriate personal protective equipment, such as safety glasses and gloves.
• Use only appropriate tools for the task.
• If you are unsure about any step, consult a qualified automotive technician.

3. Package Contents

Verify that all components are present and undamaged upon opening the package:

• 1 x UPPARTS Passenger Side Tail Light Assembly (Includes Lens, Housing, and Bulb)

4. Compatibility

This UPPARTS Tail Light Assembly is designed for the passenger side of the following Nissan NV models and years:

• Nissan NV1500: 2012, 2013, 2014, 2015, 2016, 2017, 2018 (S, SV trims)
• Nissan NV2500: 2012, 2013, 2014, 2015, 2016, 2017, 2018 (S, SV, SL trims)
• Nissan NV3500: 2012, 2013, 2014, 2015, 2016, 2017, 2018 (S, SV, SL trims)

5. Installation (Setup)

This section outlines the steps for replacing your vehicle's passenger side tail light assembly. The process is designed for direct replacement.

5.1. Tools Required

• Screwdriver (Phillips head or flathead, depending on vehicle fasteners)
• Socket wrench set (if bolts are used)
• Trim removal tool (optional, for plastic clips)

5.2. Preparation

1. Park the vehicle on a flat, stable surface and engage the parking brake.
2. Turn off the engine and remove the ignition key.
3. Disconnect the negative terminal of the vehicle's battery.

5.3. Removal of Existing Tail Light Assembly

1. Locate the mounting screws or bolts securing the tail light assembly to the vehicle body. These are typically accessible from the exterior or by opening the rear cargo door.
2. Carefully remove all visible fasteners.
3. Gently pull the tail light assembly straight back from the vehicle. It may be held by alignment pins or clips. Avoid excessive force to prevent damage.
4. Once the assembly is loose, disconnect the electrical wiring harness by pressing the release tab and pulling the connector apart.
5. Remove the old tail light assembly.

Image 5.3.1: Rear view of a Nissan NV van, indicating the location of the passenger side tail light assembly for removal.

Image 5.3.2: Illustrative diagram demonstrating the removal process of the tail light assembly from the vehicle's passenger side.

5.4. Installation of New Tail Light Assembly

1. Take the new UPPARTS Tail Light Assembly. Ensure the included bulb is securely seated in its socket.
2. Connect the vehicle's electrical wiring harness to the new tail light assembly. Ensure the connection is firm and the locking tab engages.
3. Align the new tail light assembly with the mounting points and alignment pins on the vehicle body.
4. Gently push the assembly into place until it sits flush with the vehicle's exterior.
5. Reinstall the mounting screws or bolts that were removed in step 5.3.2. Tighten them securely, but do not overtighten.

Image 5.4.1: Rear view of the UPPARTS Tail Light Assembly, highlighting the electrical connection points and bulb sockets for proper wiring.

5.5. Post-Installation Check

1. Reconnect the negative terminal of the vehicle's battery.
2. Turn on the vehicle's ignition and test all tail light functions: running lights, brake lights, turn signal, and reverse light.
3. Ensure all lights illuminate correctly and the turn signal flashes at the proper rate.

6. Operation

The UPPARTS Tail Light Assembly operates automatically with your vehicle's electrical system. Once installed, its functions (running light, brake light, turn signal, reverse light) will activate as intended when the corresponding vehicle controls are engaged.

7. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your tail light assembly.

• Cleaning: Periodically clean the outer lens with a soft cloth and mild automotive soap to remove dirt and debris. Avoid abrasive cleaners that could scratch the lens.
• Inspection: Regularly check the tail light for any signs of damage, cracks, or condensation inside the lens. Ensure all bulbs are functioning correctly.
• Connections: Occasionally inspect the electrical connections for corrosion or looseness.

8. Troubleshooting

If you encounter issues with your tail light assembly, refer to the following common troubleshooting steps:

• Light Not Illuminating:
  • Check the electrical connection to the tail light assembly to ensure it is securely plugged in.
  • Inspect the bulb (if replaceable) for a broken filament. Replace if necessary.
  • Check the corresponding fuse in your vehicle's fuse box. Refer to your vehicle's owner's manual for fuse locations and diagrams.
• Intermittent Function:
  • Ensure all wiring connections are tight and free from corrosion.
  • Verify the bulb is seated correctly in its socket.
• Condensation Inside Lens:
  • Minor condensation can occur due to temperature changes and usually dissipates. If excessive or persistent, check for cracks in the housing or a loose seal.

9. Specifications

Image 9.1: Front view of the UPPARTS Passenger Side Tail Light Assembly, showcasing its design and lens colors.

Image 9.2: Overview of quality assurance tests conducted on UPPARTS automotive components to ensure durability and performance.

10. Warranty

This UPPARTS Tail Light Assembly is covered by a 2-Year Unlimited Mileage Warranty. For warranty claims or questions regarding product fitment, please contact UPPARTS customer service.

11. Support

For further assistance, technical support, or inquiries regarding your UPPARTS Tail Light Assembly, please refer to the contact information provided with your purchase or visit the official UPPARTS website.