CyclingDeal Upright Bike Stand (Model: CD-KT95-V1)

1. Introduction

This manual provides comprehensive instructions for the assembly, operation, and maintenance of your CyclingDeal Upright Bike Stand. This versatile stand is designed to securely store your bicycle in both vertical and horizontal orientations, optimizing space and protecting your bike. Please read this manual thoroughly before assembly and use to ensure safe and correct operation.

2. Safety Information

• Maximum Load Capacity: Do not exceed the maximum bike weight of 44 lbs (20 kg).
• Compatibility: This stand fits bikes with wheel sizes from 24" to 29" (including 700c Road Bikes). It is NOT compatible with bikes having tires wider than 2.4" or "vintage type" rear mudguards.
• Stable Surface: Always place the bike stand on a flat, stable, and level surface to prevent tipping.
• Secure Placement: Ensure the bicycle is firmly seated in the stand's rollers and the front wheel hook (for vertical storage) is properly engaged before leaving the bike unattended.
• Children and Pets: Keep children and pets away from the bike stand and stored bicycle to prevent accidents.
• Floor Mounting: If permanent floor mounting is desired for added stability, use appropriate mounting bolts (not included) and ensure the installation surface can support the weight.

3. Package Contents

Before beginning assembly, please verify that all components are present and undamaged. If any parts are missing or damaged, contact CyclingDeal customer support.

• Main Frame Components (various sections)
• Adjustable Rollers (3 units)
• Front Wheel Hook
• Hardware (screws, nuts, etc.)
• Instruction Manual

4. Assembly and Setup

The CyclingDeal Upright Bike Stand is designed for straightforward assembly. Follow these steps:

1. Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, flat surface.
2. Assemble Base: Connect the base sections of the stand using the provided hardware. Ensure all connections are tight and secure.
3. Attach Vertical Support: Secure the main vertical support pole to the assembled base.
4. Install Rollers: Attach the three adjustable rollers to the designated positions on the stand. These rollers are crucial for supporting the bike's rear wheel.
5. Install Front Wheel Hook: Secure the front wheel hook to the upper section of the vertical support. This hook is adjustable to accommodate different bike sizes.
6. Adjust Rollers and Hook: The rollers and hook are fully adjustable. Adjust their positions to fit your specific bike's wheel size (24" to 29" including 700c) and tire width (up to 2.4"). This ensures a snug and stable fit.
7. Optional Floor Mounting: For enhanced stability, the rubberized feet have holes for floor mounting. If desired, secure the stand to the floor using appropriate mounting bolts (not included).

Image: Components of the CyclingDeal Upright Bike Stand ready for assembly.

Image: Compatibility details for wheel size (24"-29", 700C) and maximum tire width (2.4").

Image: Detail of the adjustable rollers and rubberized feet with optional floor mounting holes.

5. Operating Instructions

The CyclingDeal Upright Bike Stand offers two primary storage modes: vertical and horizontal.

5.1 Vertical Storage

1. Position Stand: Place the stand on a stable, level surface.
2. Wheel Bike In: Roll the rear wheel of your bicycle into the lower cradle formed by the adjustable rollers.
3. Lift Upright: Carefully lift the front of your bicycle, guiding it upwards until the front wheel aligns with the upper hook.
4. Engage Hook: Securely hook the front wheel onto the adjustable upper hook. Ensure the bike is balanced and stable.

Image: A mountain bike stored vertically in the stand, demonstrating space-saving.

Image: A road bike stored vertically, highlighting the stand's versatility.

5.2 Horizontal Storage

1. Position Stand: Place the stand on a stable, level surface.
2. Wheel Bike In: Roll either the front or rear wheel of your bicycle into the lower cradle formed by the adjustable rollers.
3. Secure Wheel: Ensure the wheel is centered and firmly held by the rollers. The stand's design provides stability for horizontal parking without needing the upper hook.

Image: A bicycle stored horizontally, showing the stand's low-profile use.

Image: Visual comparison of vertical and horizontal storage methods using the stand.

6. Maintenance

• Regular Cleaning: Wipe down the stand with a damp cloth to remove dust and dirt. Avoid harsh chemicals that could damage the powder-coated finish.
• Check Connections: Periodically inspect all screws and connections to ensure they remain tight. Re-tighten if necessary.
• Inspect Rollers and Hook: Check the adjustable rollers and front wheel hook for any signs of wear or damage. Ensure they move freely and securely hold the bike.
• Rubber Feet: Verify that the rubberized feet are intact and providing adequate grip, especially if the stand is not floor-mounted.
• Rust Prevention: The stand features a powder-coated finish resistant to rust. However, avoid prolonged exposure to extreme moisture to maintain its condition.

7. Troubleshooting

8. Specifications

9. Warranty and Support

CyclingDeal offers a LIFE-TIME warranty on this product, reflecting our confidence in its quality and durability. For any questions, concerns, or warranty claims, please contact CyclingDeal customer support through the retailer where you purchased the product or visit the official CyclingDeal website for contact information.

Please retain your proof of purchase for warranty purposes.