Introduction
Thank you for choosing the WOODBRIDGE Contemporary Single Handle Floor Mount Freestanding Tub Filler Faucet. This manual provides detailed instructions for the safe installation, operation, and maintenance of your new faucet. Please read this manual thoroughly before beginning installation and keep it for future reference.
Image: The WOODBRIDGE Contemporary Freestanding Tub Filler Faucet with Hand Shower in Chrome Finish, showcasing its sleek design and floor-mount base.
Important Safety Information
- Always turn off the main water supply before installing or performing any maintenance on the faucet.
- Wear appropriate personal protective equipment, such as safety glasses and gloves, during installation.
- Ensure all connections are secure and leak-free before restoring water supply.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Do not use abrasive cleaners or harsh chemicals on the faucet finish, as this may damage it.
Package Contents
Verify that all components are present before beginning installation:
- Bathtub Faucet Assembly
- Brass Tube
- Hand Shower with 60" Double Spiral Stainless Steel Hose
- Hot and Cold Water Inlet Hoses
- Metal Tripod with Mounting Hardware
- Base Cover
- Installation Instruction Manual (this document)
Product Specifications
| Brand | WOODBRIDGE |
| Model Number | F0046CH |
| Color | Chrome |
| Material | Brass, Ceramic |
| Finish Type | Chrome Finish |
| Number of Handles | 1 |
| Mounting Type | Floor Mount |
| Overall Size (L x W x H) | 6-1/4" x 6-1/4" x 43-1/2" |
| Spout Height | 43-1/2" |
| Spout Reach | 8-3/4" |
| Spout Clearance | 40" |
| Max Spout Flow Rate | 8.0 GPM at 80 PSI |
| Max Hand Shower Flow Rate | 1.8 GPM at 80 PSI (meets CEC requirement) |
| Connection Standard | 1/2" IPS |
| Certifications | ICC-ES listed, compliance with ASME A112.18.1-2018 and CSA B125.1-18 |
Image: Detailed technical drawing showing the dimensions of the faucet, including overall height, spout height, spout reach, and base dimensions.
Installation Guide
1. Pre-Installation
- Ensure you have all necessary tools: adjustable wrench, pipe wrench, screwdriver, tape measure, level, drill (if needed for mounting).
- Turn off the main water supply to the installation area.
- Clear the installation area and ensure sufficient space for the faucet and tub.
2. Mounting the Faucet
- Position the metal tripod mounting bracket on the floor where the faucet will be installed. Ensure it is level and in the desired location relative to your bathtub.
- Mark the drilling points through the holes in the tripod bracket.
- Drill pilot holes into the floor at the marked locations. For concrete floors, use the provided expansion bolts.
- Secure the tripod mounting bracket to the floor using the appropriate mounting hardware. Ensure it is firmly attached.
- Feed the hot and cold water inlet hoses through the center opening of the tripod bracket.
3. Connecting Water Lines
- Connect the hot and cold water inlet hoses from the faucet assembly to your existing hot and cold water supply lines. Use an adjustable wrench to tighten connections, but do not overtighten.
- Ensure all connections are sealed properly to prevent leaks. It is recommended to use plumber's tape on threaded connections.
- Carefully place the faucet assembly onto the secured tripod mounting bracket, aligning the base with the bracket.
- Secure the faucet assembly to the tripod using the provided fasteners, typically from underneath the base.
- Slide the base cover down to conceal the mounting hardware and connections.
After installation, slowly turn on the main water supply and check for any leaks. If leaks occur, tighten the connections as needed.
Operating Instructions
1. Faucet Operation
- The faucet features a single handle for controlling both water flow and temperature.
- To turn on the water, lift the handle.
- To increase water flow, lift the handle further.
- To adjust temperature, pivot the handle left for hot water and right for cold water.
- To turn off the water, push the handle down to its original position.
Image: The faucet in operation, demonstrating the water flow into a freestanding bathtub.
2. Hand Shower Use
- To activate the hand shower, pull the diverter knob located on the faucet body. Water will divert from the main spout to the hand shower.
- To return water flow to the main spout, push the diverter knob back in.
- The hand shower is ideal for rinsing, hair washing, tub cleaning, and washing pets.
Image: A hand holding the hand shower, demonstrating its spray function and flexibility for various uses.
Care and Maintenance
- Cleaning: To maintain the finish of your faucet, wipe it with a soft, damp cloth after each use. This helps prevent water spots and mineral buildup.
- Avoid Harsh Cleaners: Do not use abrasive cleaners, ammonia-based products, bleach, or other harsh chemicals, as these can damage the chrome finish and internal components.
- Stubborn Stains: For more stubborn stains, use a mild soap and water solution, then rinse thoroughly and dry with a soft cloth.
- Aerator Cleaning: Periodically unscrew the aerator from the spout and clean any mineral deposits or debris to maintain optimal water flow.
Troubleshooting
| Problem | Possible Cause / Solution |
|---|---|
| Low Water Flow |
|
| Leaks from Faucet Base |
|
| Water Not Diverting to Hand Shower |
|
| Inconsistent Water Temperature |
|
If you encounter issues not listed here or if the problem persists after attempting these solutions, please contact WOODBRIDGE customer support.
Warranty and Support
WOODBRIDGE products are designed for quality and durability. This product is ICC-ES listed and complies with ASME A112.18.1-2018 and CSA B125.1-18 standards.
For warranty information, product support, or assistance with any sales or product queries, please contact the WOODBRIDGE product support team. You can find contact details on the official WOODBRIDGE website or through your purchase documentation.
Visit the official WOODBRIDGE store for more information: WOODBRIDGE Store on Amazon