Introduction
This manual provides essential instructions for the installation, operation, and maintenance of your Manxrtod FX801R Replacement Blades. These blades are designed for compatibility with specific professional clippers, ensuring optimal performance when properly installed and cared for.
The Manxrtod FX801R replacement blades are compatible with Barberology FX870, FXF880, FX810, FX825, and FX673N clippers.
Product Features
- Professional Precision: Designed for Barberology FX870, FXF880, FX810, FX825, and FX673N clippers.
- Durable Construction: Made from 440C carbon steel with a DLC (Diamond-Like Carbon) surface treatment for enhanced sharpness and longevity.
- Optimized Performance: Engineered for cooler operation and superior cutting efficiency compared to standard blades.
- Easy Installation: Designed for straightforward replacement of existing clipper blades.
Image: The Manxrtod FX801R replacement blade highlighting its excellent performance characteristics, including cooler operation and enhanced sharpness.
Installation Guide
Before beginning, ensure your clipper is turned off and unplugged for safety. Handle blades carefully to avoid injury.
- Remove Old Blades: Using a screwdriver, carefully unscrew the two screws holding the existing blades to the clipper head. Remove both the fixed and moving blades.
- Clean Clipper Head: Clean any hair or debris from the clipper head area using a small brush.
- Position New Blades: Place the new Manxrtod FX801R fixed blade onto the clipper head, aligning the screw holes. Then, place the moving blade on top of the fixed blade, ensuring it sits correctly within the guides.
- Secure Blades: Insert the screws and gently tighten them. Ensure the blades are aligned properly, with the cutting edge of the moving blade slightly behind the fixed blade to prevent skin nicks. The blades should be parallel and centered.
- Test Alignment: Turn on the clipper briefly to check for proper blade movement and alignment. Adjust screws if necessary to achieve optimal alignment and smooth operation.
Image: The Manxrtod FX801R replacement blade set, showing the fixed and moving blade components ready for installation.
Operating Instructions
Once installed, the Manxrtod FX801R replacement blades operate identically to the original blades of your compatible clipper. Ensure the blades are always clean and lightly oiled before each use for best cutting performance and to prolong blade life.
- Always use the clipper on clean, dry hair.
- Apply light pressure and move the clipper smoothly against the direction of hair growth.
- Regularly check blade temperature during extended use to prevent overheating.
Care and Maintenance
Proper maintenance is crucial for the longevity and performance of your replacement blades.
- Cleaning: After each use, brush off any loose hair from the blades. For a deeper clean, you may use a blade cleaning spray or carefully wipe with a damp cloth (ensure clipper is unplugged). Allow blades to dry completely before oiling.
- Oiling: Apply 1-2 drops of clipper oil to the teeth of the blades before and after each use. Turn on the clipper for a few seconds to distribute the oil evenly. This reduces friction, heat, and wear.
- Storage: Store the clipper with the blades attached in a clean, dry place, protected from dust and moisture.
Image: Illustration of the Manxrtod FX801R blade's superior craftsmanship, highlighting its 440C carbon steel and DLC surface finish for durability.
Troubleshooting
Refer to the table below for common issues and their potential solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Blades pulling or snagging hair | Blades are dull, dirty, or not properly oiled. | Clean and oil blades. If issue persists, blades may need replacement. |
| Blades not cutting effectively | Improper blade alignment or loose screws. | Ensure blades are securely fastened and correctly aligned. Refer to Installation Guide. |
| Excessive noise or vibration | Blades are loose or misaligned. | Tighten blade screws and check alignment. Ensure no debris is lodged between blades. |
| Blades getting hot quickly | Lack of lubrication or prolonged use without cleaning. | Apply clipper oil generously. Clean blades thoroughly. Allow clipper to cool if used for extended periods. |
Product Specifications
- Model: FX801R
- Material: 440C Carbon Steel with DLC Surface Treatment
- Dimensions (Fixed Blade): Approximately 4.5 cm (1.77 inches) width x 3.7 cm (1.45 inches) height
- Dimensions (Moving Blade): Approximately 4.0 cm (1.57 inches) width x 2.1 cm (0.8 inches) height
- Weight: 1.6 ounces (total product weight)
- Compatibility: Barberology FX870, FXF880, FX810, FX825, FX673N Clippers
Image: Detailed diagram showing the dimensions of the Manxrtod FX801R fixed and moving blades.
Compatible Clipper Models
These replacement blades are specifically engineered to fit the following professional clipper models:
- Barberology FX870
- Barberology FXF880
- Barberology FX810
- Barberology FX825
- Barberology FX673N
Image: A visual representation of several Barberology clipper models (FX870G, FX870N, FX870RG, FX870S, FX825) that are compatible with the Manxrtod FX801R replacement blades.
Customer Support
For any questions, concerns, or issues regarding your Manxrtod FX801R Replacement Blades, please contact our customer support team. We are committed to providing assistance and will respond to inquiries within 12 hours.
Please ensure that the blade fits your machine before purchase. If you encounter any problems, do not hesitate to reach out.
Warranty Information: Specific warranty details are not provided in this manual. Please refer to the product packaging or contact customer support for warranty-related inquiries.