FUNCHDAY 13-inch Wireless Remote Dimmable Picture Light Instruction Manual

Introduction

This manual provides essential instructions for the safe and efficient use of your FUNCHDAY 13-inch Wireless Remote Dimmable Picture Light. Please read this manual thoroughly before installation and operation, and retain it for future reference.

Image: The FUNCHDAY 13-inch Wireless Remote Dimmable Picture Light, shown with its remote control and USB charging cable.

What's in the Box

Verify that all components are present before proceeding with installation:

• 1 x FUNCHDAY Picture Light (13-inch, Antique Brass)
• 1 x Remote Control
• 1 x Micro USB Charging Cable (39 inches / 100 cm)
• 2 x Mounting Screws
• 2 x Expansion Pillar Hinges (Wall Anchors)
• 1 x User Manual (This document)

Specifications

Setup and Installation

Follow these steps to properly install your picture light:

1. Prepare Mounting Location: Select a suitable location on the wall. Drill two pilot holes at the desired mounting points. Ensure the distance between the holes matches the mounting bracket on the light. Insert the expansion pillar hinges (wall anchors) into the pilot holes.
2. Attach Mounting Bracket: Place the metal mounting plate over the drilled holes. Insert the screws into the expansion pillar hinges and tighten them slightly until the bracket is secure, but do not fully tighten yet.
3. Level and Secure: Use a level to ensure the mounting bracket is perfectly horizontal. Once level, fully tighten the screws to secure the bracket firmly to the wall. Avoid over-tightening.
4. Hang the Picture Light: Align the picture light with the mounting bracket. Slide the light unit downwards onto the bracket until it locks into position.
5. Remove for Charging (Optional): To remove the picture light from the mounting bracket, hold the light by its base (not the light head). Slide the unit upwards until it releases from the bracket, then pull it away from the wall.

Image: A diagram illustrating the dimensions of the picture light and the steps for wall mounting using screws and a metal plate.

Operating Instructions

Adjusting the Light Direction

The light tube can be rotated up to 150 degrees vertically. Gently adjust the light head to direct illumination precisely onto your artwork or display.

Image: A detailed view highlighting the 150-degree rotatable light tube and key product specifications.

Using the Remote Control

The included remote control provides comprehensive functionality:

• ON/OFF: Press the 'ON' button to turn the light on, and 'OFF' to turn it off.
• Dimmable: Use the '+' button to increase brightness and the '-' button to decrease brightness.
• Timer: Press the '1H', '2H', '3H', or '4H' buttons to set the light to automatically turn off after 1, 2, 3, or 4 hours, respectively.
• Timer Reset: Press the 'RESET' button to cancel any active timer setting.

Image: The remote control in use, demonstrating its ON/OFF, timer, and dimmable features.

Using the Manual Switch

A manual touch switch is located on the side of the light fixture:

• Turn On/Off: Press the switch once to turn the light on or off.
• Dimmable: When the light is on, press and hold the switch to adjust the brightness level. Release when the desired brightness is reached.

Image: A close-up of the manual touch switch, demonstrating its dimmable functionality.

Charging Instructions

The picture light is powered by a rechargeable battery. To charge:

1. Locate the charging port on the side of the light fixture.
2. Connect the included Micro USB charging cable to the charging port.
3. Connect the other end of the USB cable to a compatible USB power source (e.g., power bank, computer USB port, USB wall adapter, car charger).
4. A blue LED indicator light will illuminate during charging. The indicator will turn off once the battery is fully charged.

The charging cable is 39 inches (100 cm) long, allowing for convenient charging without necessarily removing the light from the wall.

Image: Illustrations of the charging port and various compatible USB power sources for recharging the picture light.

Maintenance

To ensure the longevity and optimal performance of your picture light:

• Cleaning: Gently wipe the light fixture with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these may damage the finish.
• Battery Care: For best battery life, avoid fully discharging the battery frequently. Recharge the light when brightness noticeably diminishes. If storing the light for an extended period, charge it to approximately 50% every few months.
• Indoor Use Only: This product is designed for indoor use. Do not expose it to moisture or extreme temperatures.

Troubleshooting

If you encounter issues with your picture light, refer to the following common solutions:

• Light Not Turning On:
  • Ensure the battery is charged. Connect the light to a power source and check the blue LED indicator.
  • Verify that the remote control batteries are functional.
  • Try operating the light using the manual touch switch to rule out a remote control issue.
• Remote Control Not Responding:
  • Ensure there are no obstructions between the remote and the light.
  • Check and replace the remote control battery if necessary.
  • Ensure you are within the effective range of the remote control.
• Short Battery Life:
  • Battery life varies with brightness settings. Higher brightness consumes more power.
  • Ensure the light is fully charged before use (blue LED indicator turns off).
  • Over time, all rechargeable batteries experience degradation.

Warranty and Support

For information regarding warranty coverage or technical support, please refer to the purchase documentation or contact FUNCHDAY customer service through the platform where the product was purchased. Keep your proof of purchase for warranty claims.