Odashen Mi Robot Vacuum-Mop 2 Pro, Mi Robot Vacuum-Mop 2 Lite, MJSTL, MJST1SHW, MJST1S

Odashen Replacement Parts Instruction Manual

For Xiaomi Mi Robot Vacuum-Mop 2 Pro 2 Lite (Models MJSTL, MJST1SHW, MJST1S)

Introduction

This instruction manual provides detailed guidance for the installation and maintenance of your new Odashen replacement parts for the Xiaomi Mi Robot Vacuum-Mop 2 Pro and 2 Lite series. Regular replacement of these components ensures optimal performance and extends the lifespan of your robot vacuum cleaner. Please read these instructions carefully before proceeding with installation.

Compatibility

These replacement parts are specifically designed for the following Xiaomi Mi Robot Vacuum-Mop models:

  • Xiaomi Mi Robot Vacuum-Mop 2 Pro
  • Xiaomi Mi Robot Vacuum-Mop 2 Lite
  • Model MJSTL
  • Model MJST1SHW
  • Model MJST1S

Please verify your robot vacuum cleaner's model number to ensure proper fit and function. These parts are not compatible with Mi Robot Vacuum-Mop 2 or Mi Robot Vacuum-Mop 2 Pro+.

Compatibility chart showing Mi Robot Vacuum-Mop 2 Pro and 2 Lite as compatible, and Mi Robot Vacuum-Mop 2 and 2 Pro+ as incompatible.

Image: Compatibility chart for Odashen replacement parts. Shows a green checkmark for Mi Robot Vacuum-Mop 2 Pro and Mi Robot Vacuum-Mop 2 Lite, indicating compatibility. A red 'X' is shown for Mi Robot Vacuum-Mop 2 and Mi Robot Vacuum-Mop 2 Pro+, indicating non-compatibility.

Package Contents

Your Odashen replacement parts kit includes the following items:

  • 1 x Roller Brush (Main Brush)
  • 2 x Side Brushes
  • 2 x HEPA Filters
  • 2 x Mop Pads
Kit contents including mop pad, HEPA filter, and side brushes with dimensions.

Image: An overview of the replacement kit components, including a mop pad (305mm x 115mm), a HEPA filter (150mm x 49mm), and two side brushes (130mm arm length, 65mm brush length).

Setup and Installation

Before installing any replacement parts, ensure your robot vacuum cleaner is powered off and disconnected from its charging dock. For detailed instructions, refer to your robot vacuum's original user manual.

1. Roller Brush Installation

  1. Turn the robot vacuum cleaner upside down.
  2. Locate the brush cover, usually secured by two tabs or screws. Open or remove the cover.
  3. Remove the old roller brush. Clean any debris from the brush compartment.
  4. Insert the new Odashen roller brush, ensuring the ends align with the slots in the vacuum.
  5. Close the brush cover securely.
Roller brush with dimensions 7.72 inches length and 1.57 inches diameter.

Image: The roller brush, measuring approximately 7.72 inches (19.6 cm) in length and 1.57 inches (4 cm) in diameter, highlighting its dimensions.

Close-up view of the roller brush.

Image: A detailed view of the roller brush, showing its orange body with black bristles and the end caps for installation.

2. Side Brush Installation

  1. Turn the robot vacuum cleaner upside down.
  2. Locate the side brush(es). Depending on your model, they might be secured by a screw.
  3. Unscrew and remove the old side brush(es).
  4. Align the new Odashen side brush with the post and press it down firmly until it clicks into place, or secure it with the screw if applicable.
Single side brush with three white bristles.

Image: A single white side brush with three arms, designed to sweep debris into the vacuum's path.

3. HEPA Filter Installation

  1. Open the top cover of your robot vacuum cleaner to access the dustbin.
  2. Remove the dustbin from the vacuum.
  3. Open the dustbin cover and remove the old HEPA filter.
  4. Insert the new Odashen HEPA filter into the designated slot in the dustbin, ensuring it is seated correctly.
  5. Close the dustbin cover and reinsert the dustbin into the vacuum.

4. Mop Pad Installation

  1. Locate the water tank or mop attachment on your robot vacuum cleaner.
  2. Remove the old mop pad, typically attached with hook-and-loop fasteners.
  3. Attach the new Odashen mop pad to the water tank or mop attachment, ensuring it is securely fastened.
  4. Reattach the water tank/mop attachment to the vacuum if it was removed.

Operating with New Parts

After installing the new replacement parts, you can resume normal operation of your Xiaomi Mi Robot Vacuum-Mop. The new components are designed to restore the vacuum's cleaning efficiency. If you notice any unusual noises or performance issues, power off the vacuum and recheck the installation of all parts.

Maintenance

Regular maintenance of your replacement parts is crucial for sustained performance.

  • Roller Brush: Clean the roller brush weekly by removing hair and debris tangled around it. Use the cleaning tool provided with your vacuum, if available.
  • Side Brushes: Check side brushes regularly for wear and tear. Remove any tangled hair or debris. If bristles are bent or damaged, replace the brush.
  • HEPA Filter: Tap the filter gently to remove dust after each use. Do not wash the HEPA filter with water, as this can damage the filter material. Replace the filter every 3-6 months, or more frequently depending on usage.
  • Mop Pads: Wash mop pads after each use. They can be hand-washed or machine-washed with mild detergent. Allow them to air dry completely before reattaching.

Troubleshooting

If you encounter issues after replacing parts, consider the following:

  • Reduced Suction: Ensure the HEPA filter is correctly installed and not clogged. Check the dustbin for proper seating.
  • Poor Sweeping: Verify that side brushes are securely attached and not damaged. Remove any hair or debris preventing them from rotating freely.
  • Unusual Noises: Check the roller brush compartment for any foreign objects or improperly installed parts. Ensure the roller brush rotates freely.
  • Ineffective Mopping: Ensure the mop pad is clean and properly attached to the water tank. Check if the water tank is filled and correctly installed.

Specifications

Approximate dimensions of the replacement parts:

  • Roller Brush: Length 7.72 inches (19.6 cm), Diameter 1.57 inches (4 cm)
  • Side Brush: Arm length 5.12 inches (13 cm), Brush length 2.56 inches (6.5 cm)
  • HEPA Filter: Length 5.91 inches (15 cm), Width 1.93 inches (4.9 cm)
  • Mop Pad: Length 12.01 inches (30.5 cm), Width 4.53 inches (11.5 cm)

Warranty and Support

Odashen replacement parts are manufactured to high-quality standards. For any issues or questions regarding these replacement parts, please contact your retailer or Odashen customer support through the official channels. Please retain your proof of purchase for warranty claims, if applicable. Specific warranty terms may vary by region and retailer.

For further assistance, please visit the Odashen Store on Amazon.

© 2024 Odashen. All rights reserved. Xiaomi and Mi Robot Vacuum-Mop are trademarks of their respective owners.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.