1. Introduction and Safety Information
Thank you for choosing the Atmosphera Jily Pendant Lamp. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions carefully before installation and retain them for future reference.
Important Safety Warnings:
- Always disconnect the power supply at the main circuit breaker before attempting any installation, maintenance, or bulb replacement.
- Installation must be performed by a qualified electrician or a competent person in accordance with local electrical codes.
- Securely fasten the pendant lamp to the ceiling using appropriate and robust mounting hardware suitable for the ceiling material.
- Avoid exposing the lamp to moisture or direct water contact to prevent damage and electrical hazards.
- Do not exceed the maximum wattage specified for the light bulb (40W).
- Ensure the light bulb is fully cooled before attempting to replace it.
2. What's in the Box
Carefully unpack the contents and ensure all items are present and undamaged. If any parts are missing or damaged, do not proceed with installation and contact customer support.
- 1 x Jily Pendant Lamp Assembly (including shade, cable, and ceiling canopy)
Note: Light bulb (E27, max 40W) and mounting hardware for the ceiling are not included and must be purchased separately.
3. Setup and Installation
This section outlines the general steps for installing your pendant lamp. Always refer to the safety warnings in Section 1 before beginning.
Tools Required (Not Included):
- Screwdriver (Phillips and/or Flathead)
- Wire Strippers
- Drill (if required for ceiling mounting)
- Pencil
- Ladder
- Voltage Tester
Installation Steps:
- Turn off Power: Locate the main circuit breaker and turn off the power to the circuit where you will be installing the lamp. Verify the power is off using a voltage tester.
- Prepare Ceiling: If replacing an existing fixture, carefully remove it. Ensure the ceiling junction box is secure and capable of supporting the lamp's weight (approximately 1.08 kg).
- Mount Ceiling Canopy Bracket: Attach the mounting bracket (usually included with the lamp, inside the canopy) to the ceiling junction box using appropriate screws. Ensure it is firmly secured.
- Adjust Cable Length: The cable length is approximately 90 cm. Adjust the cable to your desired hanging height by feeding it through the ceiling canopy. Secure the cable at the desired length using the provided strain relief mechanism within the canopy.
- Wire Connections: Connect the electrical wires from the lamp to the corresponding wires from the ceiling. Typically, connect live (brown/black) to live, neutral (blue) to neutral, and ground (green/yellow) to ground. Use appropriate wire connectors. Ensure all connections are secure.
- Attach Ceiling Canopy: Carefully push the ceiling canopy up against the ceiling, covering the wiring. Secure it to the mounting bracket using the screws provided.
- Install Light Bulb: Screw an E27 base light bulb (max 40W, not included) into the lamp holder. Do not overtighten.
- Restore Power: Turn the power back on at the main circuit breaker.
- Test Lamp: Turn on the light switch to ensure the lamp functions correctly.
Image: Detail of the ceiling canopy, showing the connection point to the ceiling.
Image: The Jily pendant lamp, showcasing its full design and illuminated bulb.
4. Operating Instructions
The Atmosphera Jily Pendant Lamp is designed for simple operation.
- Turning On/Off: Control the lamp using a standard wall light switch connected to the circuit.
- Light Bulb: This fixture uses one E27 base light bulb. For optimal performance and light quality, choose a bulb that suits your preference (e.g., LED, incandescent, warm white).
Image: The Jily pendant lamp installed in a living space, demonstrating its aesthetic and light output.
5. Maintenance
Regular maintenance will help preserve the appearance and functionality of your pendant lamp.
Cleaning:
- Dusting: Regularly use a soft, dry duster or a microfiber cloth to gently remove dust from the lampshade and other surfaces.
- Spot Cleaning: For stubborn marks, lightly dampen a cloth with water (do not use harsh chemicals or abrasive cleaners) and gently wipe the affected area. Avoid excessive moisture, especially on the paper shade.
Light Bulb Replacement:
- Turn off Power: Always turn off the power to the lamp at the main circuit breaker and the wall switch before replacing the bulb.
- Allow to Cool: Ensure the old bulb has completely cooled down before touching it.
- Remove Old Bulb: Carefully unscrew the old E27 bulb counter-clockwise.
- Install New Bulb: Screw in a new E27 bulb (max 40W) clockwise until snug. Do not overtighten.
- Restore Power: Turn the power back on and test the new bulb.
Image: Detailed view of the paper and iron lampshade material.
6. Troubleshooting
If you encounter issues with your pendant lamp, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | No power to the circuit. | Check the circuit breaker and wall switch. |
| Lamp does not turn on. | Light bulb is faulty or loose. | Ensure the bulb is screwed in tightly. Replace the bulb if necessary (see Section 5). |
| Lamp flickers. | Loose bulb or wiring connection. | Turn off power, check bulb tightness. If flickering persists, consult a qualified electrician to check wiring connections. |
| Lamp is dim. | Low wattage bulb or incompatible bulb type. | Ensure the bulb wattage is appropriate and the bulb type is compatible with the fixture. |
If the problem persists after attempting these solutions, please contact a qualified electrician or customer support.
7. Specifications
| Model Name | Jily |
| Model Number | 3560232579516 |
| Brand | ATMOSPHERA CREATEUR D'INTERIEUR |
| Dimensions (L x W x H) | 48L x 38W x 48H cm (approx. D48 cm) |
| Cable Length | 90 cm |
| Item Weight | 1.08 Kilograms |
| Shade Material | Iron, Paper |
| Rope Material | Copper |
| Cable Material | Polyvinyl Chloride (PVC) |
| Canopy Material | Iron |
| Color | Beige (Shade), Black (Cable/Canopy) |
| Bulb Base | E27 |
| Max Wattage | 40 Watts |
| Number of Light Sources | 1 |
| Power Source | Corded Electric |
| Indoor/Outdoor Use | Indoor Use Only |
| Mounting Type | Ceiling Mount (Pendant) |
8. Warranty and Support
Specific warranty information for the Atmosphera Jily Pendant Lamp may vary by region and retailer. Please refer to your purchase documentation or contact the retailer where you purchased the product for details regarding warranty coverage.
For technical support, missing parts, or further assistance, please contact the customer service department of ATMOSPHERA CREATEUR D'INTERIEUR or your retailer.
When contacting support, please have your model name (Jily) and model number (3560232579516) available.