Technical Precision XBO 180W 45C OFR

Technical Precision Replacement Lamp Instruction Manual

Model: XBO 180W 45C OFR

1. Introduction

This manual provides essential information for the safe and effective use of your Technical Precision replacement lamp for the Sylvania XBO 180W 45C OFR. Please read these instructions carefully before installation and operation. Retain this manual for future reference.

2. Safety Information

  • Electrical Hazard: Always disconnect power to the equipment before attempting installation or removal of the lamp. Failure to do so can result in electric shock or injury.
  • High Temperature: Lamps operate at high temperatures. Allow the lamp to cool completely before handling to prevent burns.
  • Fragile Component: The lamp contains glass and delicate internal components. Handle with extreme care to avoid breakage. Do not touch the glass bulb directly with bare hands, as oils can reduce lamp life. Use gloves or a clean cloth.
  • Eye Protection: Do not look directly at the lamp when it is operating, as intense light can cause eye damage.
  • Disposal: Dispose of used lamps according to local regulations. Some lamps may contain materials that require special disposal procedures.

3. Product Overview

The Technical Precision XBO 180W 45C OFR is a high-quality replacement lamp designed to meet the specifications of the original Sylvania XBO 180W 45C OFR lamp. It is intended for use in compatible equipment requiring this specific lamp model.

Technical Precision XBO 180W 45C OFR replacement lamp, front view with connector

Figure 1: Front view of the Technical Precision XBO 180W 45C OFR replacement lamp, showing the bulb and attached electrical connector.

This replacement lamp features a wattage of 180W and operates at 14 Volts, producing a color temperature of 6200 Kelvin. Its average operational life is approximately 500 hours.

4. Setup and Installation

  1. Power Disconnection: Ensure the equipment is completely powered off and unplugged from the main power source.
  2. Cool Down: If replacing an existing lamp, allow sufficient time for the old lamp to cool down completely before handling.
  3. Access Lamp Compartment: Refer to your equipment's original instruction manual for specific steps on how to safely access the lamp compartment.
  4. Remove Old Lamp: Carefully disconnect any electrical connectors and unfasten the old lamp from its housing. Handle the old lamp with care, especially if it is broken.
  5. Install New Lamp:
    • Wearing clean gloves or using a clean cloth, carefully remove the new Technical Precision lamp from its packaging. Avoid touching the glass bulb directly.
    • Align the lamp with its housing and gently insert it. Ensure it is seated correctly and securely.
    • Connect the electrical connector firmly.
  6. Secure Compartment: Close and secure the lamp compartment according to your equipment's manual.
  7. Power On: Reconnect the equipment to the power source and power it on.
Close-up view of the Technical Precision XBO 180W 45C OFR lamp's bulb element

Figure 2: Close-up view of the lamp's bulb element, highlighting the delicate nature of the component.

5. Operating Instructions

Once installed, the Technical Precision XBO 180W 45C OFR lamp operates as part of your equipment. Refer to your equipment's instruction manual for specific operating procedures.

  • Initial Power-Up: The lamp may require a brief warm-up period to reach full brightness and stable operation.
  • Cool-Down Period: After turning off the equipment, allow a cool-down period before restarting. Frequent immediate restarts can reduce lamp life.

6. Maintenance

The Technical Precision replacement lamp is a sealed unit and does not require user maintenance beyond proper handling and timely replacement.

  • Cleaning: Do not attempt to clean the lamp bulb. If dust accumulates on the exterior housing or reflector, gently wipe with a dry, lint-free cloth after ensuring the lamp is cool and power is disconnected.
  • Replacement: Replace the lamp when its brightness diminishes significantly or when it ceases to function. The average life is approximately 500 hours, but actual life may vary based on usage conditions.
  • Disposal: Dispose of the used lamp responsibly. Consult local waste management authorities for proper disposal methods for high-intensity discharge lamps.
View of the electrical connector for the Technical Precision XBO 180W 45C OFR lamp

Figure 3: The electrical connector, which must be securely attached during installation.

7. Troubleshooting

ProblemPossible CauseSolution
Lamp does not light up.
  • No power to equipment.
  • Lamp not properly installed.
  • Electrical connector loose.
  • Lamp has reached end of life.
  • Equipment fault.
  • Check power supply to equipment.
  • Ensure lamp is securely seated.
  • Verify electrical connector is firm.
  • Replace lamp if it has exceeded its average life.
  • Consult equipment manual for further diagnostics.
Lamp is dim or flickers.
  • Lamp nearing end of life.
  • Insufficient power supply.
  • Internal equipment issue.
  • Replace lamp.
  • Check power connections and supply.
  • Consult equipment manual or qualified technician.

8. Specifications

  • Model: XBO 180W 45C OFR
  • Brand: Technical Precision
  • Wattage: 180 Watts
  • Voltage: 14 Volts
  • Color Temperature: 6200 Kelvin
  • Average Life: 500 Hours
  • Bulb Length: 3.54 Inches
  • Included Components: 1 x Replacement Lamp

9. Warranty and Support

For warranty information regarding your Technical Precision replacement lamp, please refer to the documentation provided at the time of purchase or contact the seller directly. Technical Precision is the manufacturer of this replacement part.

For technical support or inquiries, please contact the retailer or Technical Precision customer service through their official channels.