Elation Lighting Obsidian NX-P Motorized Fader Wing for ONYX User Manual

1. Introduction

The Elation Lighting Obsidian NX-P is a motorized fader wing designed to expand the control capabilities of ONYX lighting systems. It serves as an ideal companion for the NX1 console and ONYX PC systems, replicating the full playback section found on the NX1 console.

This device offers direct connectivity to your lighting system via four integrated DMX ports. Multiple NX-P wings can be connected to any ONYX console or PC system, providing expanded direct access with 20 playbacks simultaneously. The flexible button array can be configured for playback control or as powerful function keys.

The NX-P maintains the layout and functionality of the NX1 and NX4 console surfaces, ensuring seamless and intuitive operation. It features a magnetic alignment system for easy attachment to an NX1 console or NX K command pad. As part of the ONYX platform, this keypad and playback wing is compatible with all other NX devices and ONYX PC systems.

2. Safety Information

Please read and understand all safety instructions before operating this device. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• Power Supply: Before operation, ensure that the voltage and frequency of your local power supply match the requirements specified on the device label.
• Servicing: Disconnect the unit from the mains power before performing any servicing. Refer all servicing to qualified personnel only.
• Environment: Use this device only in dry locations. Do not expose to moisture or liquids.
• Electric Shock: Risk of electric shock. Do not open the device enclosure. There are no user-serviceable parts inside.
• Intended Use: This product is not intended for household use.
• Installation: Refer to the serial number label for manufacturer's model reference and number. This device is suitable for mounting on normally combustible surfaces.

3. Product Overview

3.1 Key Features

• Portable and compact motorized playback wing.
• 10x 60 mm motorized playback faders.
• Each fader includes 4x function-assignable buttons.
• 10x customizable playback or multi-function keys.
• Dedicated Playback Select button.
• Master Go section with Go, Pause, Snap, and Release buttons.
• 4x integrated DMX ports (5-pin locking XLR).
• Includes ONYX Nova+ License (supporting 4 Universes + MIDI/OSC/Timecode).
• USB-B 2.0 input for connectivity.

3.2 Front Panel Components

• Motorized Faders (1-10): Ten 60mm motorized faders for precise control of lighting parameters.
• Fader Buttons: Four buttons associated with each fader, assignable for various functions.
• Desklight: Connector for an optional desk light.
• V/A Buttons: Used for navigation or value adjustment.
• Select Button: For selecting items or modes.
• Snap Button: Captures current states.
• Rel (Release) Button: Releases active playbacks or functions.
• I/Back Button: Used for 'Insert' or 'Back' functions.
• Go Button: Initiates cues or sequences.
• Play Button: Starts playback.
• Func (Function) Button: Accesses additional functions.
• F-Keys: Customizable function keys.

3.3 Rear Panel Connections

• DMX 1-4 (5-pin locking XLR): Four DMX/RDM Universe In/Out ports for connecting to lighting fixtures and other DMX devices.
• USB-B 2.0 Input: For connecting the NX-P to a compatible ONYX PC system or console.
• IP65 Locking Power In: Secure power input connector.
• Mains ON/OFF Switch: Power switch for the unit.
• Fuse P1: Fuse compartment. Refer to the compliance label for replacement fuse size.

4. Setup

4.1 Unpacking and Inspection

Carefully unpack the NX-P and inspect it for any damage that may have occurred during shipping. If any damage is found, contact your dealer immediately. Retain the packing materials in case the unit needs to be returned.

4.2 Connecting to Power

1. Ensure the Mains ON/OFF switch on the rear panel is in the OFF position.
2. Connect the provided power cable to the IP65 Locking Power In port on the rear panel.
3. Plug the other end of the power cable into a suitable electrical outlet (100-240 V, 50/60 Hz).

4.3 Connecting to ONYX System

1. Connect the NX-P to your ONYX PC system or NX1 console using the supplied USB cable. Insert the USB-B end into the NX-P's USB-B 2.0 input port and the other end into an available USB port on your computer or console.
2. If connecting to an NX1 console or NX K command pad, utilize the magnetic alignment system for secure physical attachment.
3. Install the necessary ONYX software and drivers on your PC if you are using an ONYX PC system. The included Nova+ License will activate 4 Universes and MIDI/OSC/Timecode support within the ONYX software.

4.4 DMX Connections

Connect your DMX-compatible lighting fixtures and devices to the DMX 1-4 ports on the rear panel using 5-pin XLR cables. Ensure proper DMX cabling practices, including termination, for reliable signal transmission.

5. Operating Instructions

5.1 Powering On/Off

1. To power on, flip the Mains ON/OFF switch on the rear panel to the ON position.
2. To power off, flip the Mains ON/OFF switch to the OFF position. Always power down the NX-P before disconnecting power or USB cables.

5.2 ONYX Software Integration

The NX-P operates as a dedicated control surface for the ONYX lighting control software. All fader and button assignments, playback configurations, and system settings are managed within the ONYX software interface. Refer to the ONYX software manual for detailed instructions on:

• Mapping faders to control specific lighting parameters or playbacks.
• Assigning functions to the 4 buttons per fader.
• Configuring the 10 customizable playback or multi-function keys.
• Utilizing the Master Go section (Go, Pause, Snap, Release) for cue control.
• Setting up DMX universes and fixture patching.
• Implementing MIDI/OSC/Timecode functionalities enabled by the Nova+ License.

5.3 Using Motorized Faders

The 60mm motorized faders provide tactile control and will automatically adjust to reflect the current values within the ONYX software. This ensures that the physical fader position always matches the software's state, especially when switching between playbacks or pages.

5.4 Playback and Function Keys

The NX-P replicates the playback section of larger ONYX consoles. Use the Playback Select button to navigate between different playback pages or banks. The customizable keys can be assigned to trigger cues, execute macros, or perform other software functions as configured in ONYX.

6. Maintenance

6.1 Cleaning

To maintain the appearance and functionality of your NX-P, regularly clean the exterior with a soft, dry cloth. For stubborn dirt, a slightly damp cloth with mild soap can be used, followed by drying. Avoid using harsh chemicals, abrasives, or solvents, as these can damage the finish and internal components.

Keep the fader tracks free of dust and debris. Compressed air can be used carefully to dislodge particles from around the faders and buttons.

6.2 Fuse Replacement

If the unit fails to power on, check the fuse located in the Fuse P1 compartment on the rear panel. Disconnect the unit from mains power before attempting to replace the fuse. Use only a fuse of the exact type and rating specified on the compliance label next to the fuse holder.

7. Troubleshooting

• Unit does not power on:
  • Ensure the power cable is securely connected to both the unit and a working electrical outlet.
  • Verify the Mains ON/OFF switch is in the ON position.
  • Check the fuse (see Section 6.2 Fuse Replacement).
• NX-P not recognized by ONYX software:
  • Ensure the USB cable is securely connected to both the NX-P and your computer/console.
  • Try a different USB port or USB cable.
  • Verify that the latest ONYX software and drivers are installed.
  • Restart the ONYX software and/or your computer/console.
• Faders or buttons not responding:
  • Confirm the NX-P is properly connected and recognized by the ONYX software.
  • Check the ONYX software for correct fader and button assignments.
  • Ensure no other software is interfering with the USB connection.
• DMX output issues:
  • Verify DMX cables are correctly connected and not damaged.
  • Check DMX termination in your lighting rig.
  • Confirm DMX universe and fixture patching settings within the ONYX software.

For further assistance, consult the comprehensive ONYX software manual or contact your authorized dealer or manufacturer support.

8. Specifications

9. What's in the Box

Upon unpacking, ensure the following items are included:

• Elation Lighting Obsidian NX-P Motorized Fader Wing
• ONYX Nova+ License
• USB Cable
• Power Cable

10. Warranty and Support

For warranty information, please refer to the documentation provided by your retailer or the manufacturer at the time of purchase. For technical support, software updates, or further assistance, please contact your authorized Elation Lighting dealer or visit the official Elation Lighting website.