Compustar CS697-A 1-Way Security System & Code Alarm DA1 Door Lock Actuators

1. Introduction and Overview

The Compustar CS697-A 1-Way Security System is designed to provide comprehensive protection for your vehicle, deterring theft and intrusion. This bundle also includes two Code Alarm DA1 Standard 2-Wire Door Lock Actuators, enabling power locking functionality for vehicles with manual locking systems.

The Compustar CS697-A system integrates vehicle security, keyless entry, and advanced detection features to safeguard your investment. The Code Alarm DA1 actuators enhance convenience by converting manual door locks to power locks.

2. Product Features

• Vehicle Security: Comprehensive protection against theft and intrusion.
• Keyless Entry: Convenient remote locking and unlocking of vehicle doors.
• Dual-Stage Shock Sensor: Detects impacts and vibrations, providing warnings for minor disturbances and full alarm for significant impacts.
• Security Control Module (CM2400): The central processing unit for the alarm system.
• Starter-Kill Relay ("E-LOCK"): Prevents the vehicle from being started when the alarm is armed, acting as a theft deterrent.
• Theft-Deterrent Security LED: A visible blue LED that indicates the system is armed, discouraging potential thieves.
• 200' Max Range: Effective operating range for the remote control.
• Code Alarm DA1 Door Lock Actuators: Converts manual door locks to power locks, requiring one actuator per door.

3. Package Contents

Please verify that all components listed below are present in your package. If any items are missing or damaged, please contact your retailer or Compustar support immediately.

• Compustar CS697-A 1-Way Security System (includes control module, wiring harness, shock sensor, security LED, and two 1-way remote controls)
• Two (2) Code Alarm DA1 Standard 2-Wire Door Lock Actuators (each includes mounting hardware and connecting rod)

Figure 3.1: Complete bundle showing the Compustar security system box, two remote controls, and two Code Alarm door lock actuators with their accessories.

Figure 3.2: Close-up view of the Compustar 1-way remote control, featuring buttons for lock, unlock, trunk release, and auxiliary functions.

Figure 3.3: The Compustar CM-2400 security control module, the main unit of the alarm system.

Figure 3.4: A single Code Alarm DA1 door lock actuator shown with its associated mounting bracket, connecting rod, screws, and clips.

4. Setup and Installation

Installation of the Compustar CS697-A security system and Code Alarm DA1 door lock actuators requires specialized knowledge of vehicle electrical systems and wiring. Professional installation by a certified automotive electronics technician is highly recommended to ensure proper functionality, prevent damage to your vehicle, and maintain product warranty.

4.1. General Installation Guidelines (Professional Recommended)

• Wiring: All wiring connections should be made securely and insulated properly to prevent short circuits. Refer to the detailed wiring diagrams provided with the product packaging (not included in this manual).
• Module Placement: The CM2400 control module should be mounted in a secure, hidden location within the vehicle's interior, away from moisture and excessive heat.
• Shock Sensor: The dual-stage shock sensor should be mounted on a rigid surface, typically under the dashboard, to accurately detect impacts. Its sensitivity can usually be adjusted after installation.
• Security LED: The theft-deterrent LED should be mounted in a visible location, such as on the dashboard or windshield pillar, to act as a visual deterrent.
• Door Lock Actuators: Each DA1 actuator must be mounted within the door panel, connected to the existing manual lock mechanism using the provided rod and bracket. Proper alignment is crucial for smooth operation.
• Testing: After installation, thoroughly test all functions, including arming/disarming, keyless entry, shock sensor response, and door lock/unlock operations.

Note: Incorrect installation can lead to system malfunction, vehicle damage, or voiding of the product warranty. Always consult the full installation guide provided with your product or seek professional assistance.

5. Operating Instructions

The Compustar CS697-A system operates primarily via the included 1-way remote controls.

5.1. Remote Control Functions

• Lock Button: Press once to arm the security system and lock the vehicle doors. The security LED will begin to flash.
• Unlock Button: Press once to disarm the security system and unlock the vehicle doors. The security LED will turn off.
• Trunk Release Button (Car Icon): Press and hold to activate the vehicle's trunk release (if connected and supported by your vehicle).
• Auxiliary Button (Asterisk Icon): This button can be programmed for various auxiliary functions, depending on your installer's configuration (e.g., remote start, power sliding door, etc.). Consult your installer for specific functionality.

5.2. Security System Alerts

• Dual-Stage Shock Sensor:
  • Light Impact: A series of chirps or a short siren burst will sound to warn away potential threats.
  • Heavy Impact/Intrusion: The full alarm siren will sound, and the vehicle's lights may flash.
• Theft-Deterrent LED: A flashing blue LED indicates the system is armed and active. A rapid flash may indicate a triggered alarm event.
• Starter-Kill: When the system is armed, the starter-kill relay prevents the engine from cranking, adding an extra layer of security.

6. Maintenance

The Compustar CS697-A security system and Code Alarm DA1 actuators are designed for low maintenance.

• Remote Control Batteries: Replace the batteries in your remote controls when the range decreases significantly or the LED indicator on the remote becomes dim. Refer to the remote's specific instructions for battery type and replacement procedure.
• System Check: Periodically test all functions of your security system (arming, disarming, door locks, shock sensor) to ensure proper operation.
• Cleaning: Keep the remote controls clean and free from dirt and moisture. Do not use harsh chemicals.
• Professional Inspection: Consider having your system professionally inspected annually to ensure all components are functioning optimally and wiring connections remain secure.

7. Troubleshooting

If you experience issues with your Compustar security system or Code Alarm door lock actuators, try the following basic troubleshooting steps. For complex issues, professional assistance is recommended.

• System Not Responding to Remote:
  • Check remote control battery. Replace if necessary.
  • Ensure you are within the 200' operating range.
  • Check for strong radio interference in the area.
• Alarm Triggers Randomly:
  • The shock sensor sensitivity might be too high. Consult your installer for adjustment.
  • Check if doors, hood, or trunk are fully closed and latched.
  • Inspect wiring for any loose connections or shorts.
• Door Locks Not Operating:
  • Verify the system is disarmed.
  • Check the wiring connections to the DA1 actuators.
  • Ensure the actuator's mechanical linkage to the door lock is not obstructed or jammed.
  • A single faulty actuator may prevent others from working if wired in series; isolate the issue.
• Security LED Not Flashing:
  • System may not be armed. Try arming again.
  • Check the LED's wiring connection to the control module.

If these steps do not resolve the issue, please contact a certified Compustar installer or customer support.

8. Specifications

9. Warranty Information

The Compustar CS697-A 1-Way Security System and Code Alarm DA1 Door Lock Actuators are covered by a 1-Year Manufacturer Warranty. This warranty typically covers defects in materials and workmanship under normal use.

Please retain your proof of purchase for warranty claims. For specific terms, conditions, and limitations of the warranty, refer to the documentation included with your product or visit the official Compustar website. Unauthorized modifications or improper installation may void the warranty.

10. Support and Contact

For technical support, installation assistance, or warranty inquiries, please contact:

• Compustar Customer Support: Visit the official Compustar website for contact information, FAQs, and support resources.
• Authorized Dealer/Installer: If your system was professionally installed, contact your installer for immediate assistance. They are best equipped to diagnose and resolve installation-related issues.
• Retailer: For purchase-related issues or returns, contact the retailer from whom you purchased the product.

Always provide your product model number (COMPUBDL221230-02) and proof of purchase when seeking support.