Introduction
The Lukovee Automatic Fish Feeder is designed to provide convenient and reliable feeding for your aquarium fish. This device features a USB rechargeable battery, a clear display for feeding times and temperature, and a moisture-proof design to keep food fresh. It supports up to three feedings per day with adjustable portions and offers two versatile installation methods.
Package Contents
- 1x Lukovee Automatic Fish Feeder
- 1x USB Cable
- Instruction Manual (This Document)
Setup
1. Charging the Device
Before first use, fully charge the feeder using the provided USB cable. The battery capacity is 700mAh, and a full charge typically takes 3-4 hours. The device can be charged without disassembling it.
This image shows the feeder's USB charging port and a USB cable being connected. The feeder features a 700mAh rechargeable battery, providing 3-6 months of use on a full charge (3-4 hours charging time). The design allows charging without disassembling the unit.
2. Adding Fish Food
Open the food compartment and add your desired fish food. The feeder has a 200ml capacity. Ensure the food is dry and suitable for automatic dispensing.
3. Installation Methods
The feeder offers two primary methods for installation:
- Plane Fixing Method: Use the included double-sided sticker to fix the feeder on a flat surface of the tank cover. Ensure the feeder is positioned directly over the water and will not fall into the water.
- Vertical Fixing Method: For open fish tanks without a top cover, attach the fixing bracket to the main body and rotate the screw knob tightly. This method is suitable for tank glass with a thickness ranging from 0 to 24 mm (0.94 inch).
This image demonstrates two ways to install the feeder. Method 1 shows fixing the feeder to a flat tank cover using a double-sided sticker, ensuring it's positioned over the water. Method 2 illustrates attaching the feeder to the tank glass using an adjustable clamp base, suitable for open-top tanks. The clamp accommodates glass thickness from 0 to 24mm.
4. Temperature Probe Placement
Place the temperature probe into the water and secure it in place, typically with a suction cup (if included or attached to the probe). This allows the feeder to display the aquarium's water temperature.
This image illustrates the temperature measurement function. The feeder's display shows the current time and temperature. The temperature probe is shown with a suction cup, designed to be placed inside the aquarium to monitor water temperature. Users can switch between Fahrenheit and Celsius by pressing the '+' and '-' buttons simultaneously.
Operating Instructions
Control Panel Overview
This image provides an overview of the feeder's control panel. Key elements include the Power button, Manual Button, Power Display, 'Time' Setting button, Temperature Display, '+' Key, '-' Key, Feeding Times display, Winding Number display, and a general Setting button. These controls are used for setting time, feeding schedules, and adjusting other parameters.
1. Power ON/OFF
- To turn ON: Long press the power button for 3 seconds.
- To turn OFF: Long press the power button for 3 seconds.
2. Setting Current Time
- Long press the "Setting" button for 3 seconds. The 'Hour' number will flash.
- Press the "▲" (Up) or "▼" (Down) button to adjust the hour.
- Press the "Setting" button again. The 'Minute' number will flash.
- Press the "▲" (Up) or "▼" (Down) button to adjust the minute.
- Once the time is set, press the "Manual" key to save the current setting and exit. If you need to make further settings, press the "Setting" key again.
3. Setting Feeding Times and Cycles
The feeder supports up to 3 feeding times per day, with 1-3 cycles (windings) per feeding.
- Press the "Setting" button. The hour number for the first feeding slot will flash.
- Use "▲" (Up) or "▼" (Down) to adjust the desired feeding hour.
- Press the "Setting" button. The minute number for the first feeding slot will flash.
- Use "▲" (Up) or "▼" (Down) to adjust the desired feeding minute.
- Press the "Setting" button. The cycle number (1, 2, or 3) for the first feeding slot will flash. Use "▲" (Up) or "▼" (Down) to select the number of rotations (food portions) for this feeding. An empty display means 0 cycles.
- Repeat steps 1-5 for the second and third feeding slots if desired.
- After setting all desired feeding times and cycles, press the "Manual" key to save and exit.
4. Manual Feeding
To dispense food immediately, simply press the "Manual" button.
5. Quick Set Feeding (8 AM / 8 PM)
Long press the "▲" (Up) button for 5 seconds to quickly set two feeding times: once at 8 AM and once at 8 PM.
6. Deleting All Settings
Long press the "▼" (Down) button for 5 seconds to delete all programmed feeding settings.
7. Adjusting Food Outlet Size
The feeder allows you to adjust the size of the food outlet to control the amount of food dispensed per cycle. Rotate the adjustment mechanism on the feeder to achieve the desired opening size.
8. Temperature Display
The feeder displays the current water temperature. To switch between Celsius (°C) and Fahrenheit (°F), press the "+" and "-" buttons simultaneously.
This image presents a four-step guide for using the feeder. Step 1 shows charging the device via USB. Step 2 demonstrates adding fish food to the feeder's compartment. Step 3 illustrates setting parameters using the control panel. Step 4 shows adjusting the food outlet size to control dispensed portions.
Maintenance
1. Cleaning the Food Silo
The food silo can be easily disassembled for cleaning. Hand wash only. Ensure the silo is completely dry before reassembling and adding new food to prevent moisture issues.
2. Battery Charging
Regularly check the battery indicator on the display. Recharge the feeder promptly when the battery level is low to ensure continuous operation and prevent loss of settings.
Troubleshooting
- Feeder not dispensing food:
- Check if the feeder is powered on.
- Verify that feeding times are correctly set.
- Ensure the food outlet is not blocked or too small for the food type.
- Check the battery level; a low battery may prevent operation.
- Settings are lost:
- If the battery runs down completely, settings may be deleted. Ensure the feeder is regularly charged to maintain programmed settings.
- Inaccurate temperature reading:
- Ensure the temperature probe is fully submerged in the water and securely placed.
- Check for any damage to the probe or its connection.
- Food getting wet or clumping:
- Ensure the food silo is properly sealed after adding food.
- Verify that the feeder is installed correctly and not exposed to excessive moisture or splashing from the tank.
- Use dry, non-hygroscopic fish food.
Specifications
| Model Number | LUP132-BL-NA |
| Dimensions (Unit) | 15 x 6.8 x 11 cm (5.9 x 2.7 x 4.3 inches) |
| Weight | 216 g |
| Material | Acrylonitrile Butadiene Styrene (ABS), Glass |
| Food Capacity | 200 ml (6.8 Ounces) |
| Battery Type | 1 Lithium Ion (included) |
| Battery Capacity | 700 mAh |
| Charging Time | 3-4 hours |
| Usage Time (Full Charge) | 3-6 months (depending on settings) |
| Power Source | USB Power |
| Operation Mode | Automatic |
| Max. Tank Glass Thickness | 24 mm (0.94 inches) |
| Temperature Range | 10°C~36°C / 50°F~97°F |
| Temperature Accuracy | ±2°F (±1°C) |
Warranty Information
Specific warranty details are not provided in the product information. Please refer to the retailer's return policy or contact Lukovee customer support for warranty inquiries.
Customer Support
For further assistance or technical support, please contact Lukovee customer service through the platform where the product was purchased or visit the official Lukovee brand store online.