CO-Z Automatic Dual Swing Gate Opener Kit

Important Safety Information

Read and understand all instructions before installing and using this product. Failure to follow the instructions may result in serious injury or property damage. This gate opener is designed for residential or commercial security and convenience in opening and closing driveway or garden gates.

Professional installation is highly recommended to ensure proper function and safety. Always ensure the gate area is clear of people and obstructions before operation.

Warning: Moving gates can cause serious injury or death. Keep clear of the gate area. Do not allow children to play near the gate.

Package Contents

Verify all components are present before beginning installation:

Image: All components included in the CO-Z Automatic Dual Swing Gate Opener Kit.

• 2x Gate Opener Actuators
• 1x Control Box
• 2x Remote Controls
• 2x Release Keys
• Mounting Brackets (Post Pivot, Wall, Front)
• Various Screws, Nuts, and Washers
• Gate Stopper
• Infrared Photocell Sensors (Transmitter & Receiver)
• Power Cord

Product Overview & Features

The CO-Z Automatic Dual Swing Gate Opener Kit is designed for gates up to 18 feet and 660 pounds per side, offering convenience and security for your property.

Key Features:

• Powerful All-Copper Motors: Energy-efficient 50W motors smoothly open gates at 3 ft. per minute.
• Customizable Closing Times: Set automatic closing times for 15, 30, 60, or 90 seconds.
• Built to Withstand Any Weather: Solid construction with IP44 casing, resistant to rain, dust, and dirt, operating from -4°F to 158°F.
• Safe and Reliable Operation: Stops and reverses direction if people or vehicles are detected.
• Durable Construction: Features an aluminum actuator and durable ABS casing for long-lasting service.

Visual Features:

Image: Illustration highlighting the powerful all-copper motors for heavy-duty dual gates.

Image: Diagram showing various power options including 2x12V Lead-Acid Batteries, Solar Controller with Solar Panel, and Household Power.

Image: Visual representation of features like Auto Close with presets, Obstacle Detection with Auto Rebound, High-End Encryption Remote Control, Optional Inward/Outward Opening Direction, and Weather & Corrosion Resistant Build.

Image: Close-up views of pure copper motors, aluminum actuators, waterproof casing, and convenient gate stop.

Image: Control box showing compatibility with Solar Panel, Alarm Lights, Digital Keypads, Bluetooth Device, and Wall Switch.

Image: Dimensions of the gate opener actuators, indicating max capacity of 660 lb and max length of 18 ft for a single gate.

Image: Diagrams illustrating 'Push to Open' and 'Pull to Open' configurations for the gate opener.

Installation Guide

Follow these steps carefully for proper installation. Refer to the provided videos for visual guidance.

1. Pre-Installation Check

Determine the gate moving direction (Push-to-Open or Pull-to-Open) and verify adequate space on the hinge and gate for bracket installation. Consult the manual's diagrams for precise measurements.

2. Gate Stopper Installation

Place the limit stop at the gate's fully closed position. Drill 4 holes and insert the expansion bolts to secure it.

3. Wall Bracket Installation

Attach the post brackets to the post pivot bracket using M8 screws, nuts, and washers. Secure the post bracket to the gate post with expansion bolts. Determine an appropriate mounting height for the brackets, ensuring the actuator's apex can be attached to your gate. Mark where you need to drill and use an 8mm drill bit. Use expansion or self-tapping bolts (M8x80 or larger) based on your gate's material.

4. Actuator Installation

Unlock the motor and fully extend the opener. Fix the front bracket to the gate opener and mount it in the predetermined spot on the gate. Ensure the front bracket doesn't interfere with the gate. Connect the end of the actuator to the other bracket with the long mounting bolt. Use a level to ensure the actuator is installed horizontally. Mark the installation position of the other bracket and drill holes. Again, choose appropriate bolts based on your gate's material.

5. Control Box Installation & Wiring

Install the control box at a convenient height. Pass the motor wires through the holes and connect motor 1 and 2 in the "- - + +" order. Connect motor 1's yellow wire to EM1, blue wire to LM1, motor 2's yellow wire to EM2, and blue wire to LM2. Pass the power wire through the hole and connect it to the power terminal. Connect one end to the control box and the other end to a power outlet.

6. Infrared Photocell Setup

Have a 2-core cable and a 4-core cable ready. Connect the 2-core cable to terminals V+ and V- of the transmitter. Connect the 4-core cable to terminals V+, V-, COM, and NC of the receiver. Take the other end of the cables and twist the positive and negative ends together. Connect the wire that transmits infrared signals to port 6 and connect the wire that is attached to COM to port 5. Connect the twisted positive and negative ends to ports 13 and 14. Use extension cords if the wires are not long enough.

7. Travel Setting

Unlock the gate opener, move the gate to the fully open position, then reversely rotate the manual release bar to lock. Press the "TS1" button until "AU" shows, then release the button. The control board will set opening and closing travel automatically. Till the gate is fully closed and the display shows "--" travel setting is finished. Open your door manually and see if it moves smoothly. If there's any sticking, check if the bracket positioning matches the instructions in the manual.

8. Set the Remote Control

To enter into the remote control mode, hold TS2 until "88" is shown and press TS1 three times. "--" will be displayed. Press TS2 to enter. From here, you can cycle through standard operation where each button on the remote control can be paired independent of the others; pairing mode 1 where a remote will be paired to a gate with its first button opening the gate, its second button closing the gate, its third button partially opening the gate to allow pedestrians in, and its fourth button pausing operation; pairing mode 2 which is identical to pairing mode 1 except that third and fourth buttons are reversed; and exit.

Operation

Once installed and configured, your CO-Z Automatic Dual Swing Gate Opener provides convenient access to your property. Use the remote control to open, close, or partially open the gates. The system's obstacle detection ensures safety by stopping and reversing the gate if an obstruction is encountered.

Maintenance

Regular maintenance ensures the longevity and optimal performance of your gate opener. Perform the following checks periodically:

• Cleanliness: Keep the actuators and control box free from dirt, dust, and debris.
• Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
• Lubrication: Apply appropriate lubricant to moving parts as recommended in the detailed manual to ensure smooth operation.
• Obstacle Detection Test: Regularly test the obstacle detection feature to ensure it functions correctly.

Troubleshooting

If you encounter issues with your gate opener, refer to the common problems and solutions below. For more complex issues, consult a qualified technician.

Specifications

Warranty & Support

CO-Z offers a 2-Year Promise on this product, ensuring quality and reliability. For technical support, warranty claims, or any inquiries, please contact CO-Z customer service through their official channels.

Visit the CO-Z Store on Amazon for more information and product registration.