XPG Lancer DDR5 RGB 5600MHz 32GB RAM Kit Instruction Manual

Introduction

This manual provides essential information for the installation, operation, and maintenance of your XPG Lancer DDR5 RGB 5600MHz 32GB (2x16GB) Desktop SDRAM Memory RAM Kit. Please read these instructions carefully before proceeding with installation to ensure proper functionality and system stability.

Safety Information

Always observe the following safety precautions when handling computer components:

• Ensure your computer is powered off and unplugged from the wall outlet before installation.
• Discharge static electricity by touching a grounded metal object (e.g., the computer case) before handling memory modules. Consider using an anti-static wrist strap.
• Handle memory modules by their edges to avoid touching the gold contacts or integrated circuits.
• Do not force the memory modules into the slots. Incorrect insertion can cause damage.

Setup and Installation

Follow these steps to install your XPG Lancer DDR5 RGB memory modules:

1. Pre-installation Checklist:
   • Verify your motherboard and CPU support DDR5 memory. This RAM is not compatible with DDR4 slots.
   • Consult your motherboard manual for recommended DIMM slot population order for optimal performance (e.g., dual-channel configuration).
2. Open Computer Case: Power off your computer, unplug it, and open the side panel to access the motherboard.
3. Locate DIMM Slots: Identify the DDR5 memory slots on your motherboard. They are typically long, narrow slots with retention clips on each end.
4. Open Retention Clips: Gently push down the retention clips on both ends of the selected DIMM slot(s) to open them.
5. Align Memory Module: Hold the memory module by its edges. Align the notch on the bottom of the module with the key in the DIMM slot. The module should only fit one way.
6. Insert Memory Module: Place the module into the slot and apply firm, even pressure to both ends until the retention clips snap into place. You should hear a click.
7. Verify Installation: Ensure both retention clips are fully closed and the module is seated securely. Repeat for additional modules.
8. Close Computer Case: Once all modules are installed, close the computer case and reconnect power.

Image: Two XPG Lancer DDR5 RGB memory modules on a motherboard, one already installed and one ready for installation. This illustrates the process of inserting the RAM into the DIMM slots.

Image: Four XPG Lancer DDR5 RGB memory modules fully installed in a motherboard, showcasing their active, colorful RGB lighting.

Operating Instructions

First Boot and BIOS/UEFI Configuration

After physical installation, you may need to configure your system's BIOS/UEFI settings:

• Upon first boot, enter your system's BIOS/UEFI (usually by pressing DEL or F2 during startup).
• Navigate to the memory or overclocking settings.
• Enable the Intel XMP 3.0 or AMD EXPO profile to achieve the advertised speed of 5600MHz. These profiles automatically configure the correct timings and voltage.
• Save changes and exit BIOS/UEFI. Your system will restart with the new memory settings.

RGB Lighting Control

The XPG Lancer DDR5 RGB modules feature customizable RGB lighting. To control the lighting effects:

• Download and install the appropriate RGB synchronization software from your motherboard manufacturer's website. Compatible software includes ASUS Aura Sync, GIGABYTE RGB Fusion 2.0, MSI Mystic Light Sync, and ASRock Polychrome Sync.
• Use the software to customize colors, patterns, and brightness of the memory module's RGB lighting.

Maintenance

Proper maintenance ensures the longevity and performance of your memory modules:

• Cleaning: Periodically clean dust from inside your computer case, including around the memory modules, using compressed air. Ensure the system is powered off and unplugged before cleaning.
• Handling: Always handle memory modules by their edges. Avoid touching the gold contacts or the components on the module's surface.
• Environment: Operate your computer in a well-ventilated area to prevent excessive heat buildup, which can affect component lifespan.

Troubleshooting

If you encounter issues, refer to the following troubleshooting tips:

• System Fails to Boot or RAM Not Detected:
  • Ensure the memory modules are fully seated in their slots and the retention clips are closed.
  • Verify that your motherboard and CPU are compatible with DDR5 memory.
  • Try installing one module at a time to identify a potentially faulty module or slot.
  • Update your motherboard's BIOS/UEFI to the latest version, as this often improves memory compatibility.
• System Instability or Crashes (Blue Screens):
  • If you enabled XMP/EXPO, try disabling it in BIOS/UEFI to run the memory at its default JEDEC speed. If stability improves, the XMP/EXPO profile might be unstable with your specific CPU/motherboard combination, or a BIOS update may be needed.
  • Run a memory diagnostic tool (e.g., Windows Memory Diagnostic or MemTest86) to check for errors.
• RGB Lighting Not Working:
  • Ensure the RGB synchronization software is correctly installed and up to date.
  • Check if the software detects the memory modules.
  • Verify that the RGB headers on your motherboard (if applicable for other components) are correctly connected and configured.

Specifications

Product Overview Video

Warranty and Support

XPG memory modules are typically backed by a limited lifetime warranty. For specific warranty terms, conditions, and to register your product, please visit the official XPG website or contact XPG customer support. Keep your proof of purchase for warranty claims.

For technical assistance, driver downloads, or further support, please refer to the XPG official support channels.