Amerec 9053-407 Pro 12KW 208V 3Ph Floor Standing Sauna Heater User Manual

1. Introduction

Thank you for choosing the Amerec 9053-407 Pro 12KW 208V 3Ph Floor Standing Sauna Heater. This manual provides essential information for the safe installation, operation, and maintenance of your sauna heater. Please read all instructions carefully before installation and use to ensure proper function and longevity of the product. Keep this manual for future reference.

2. Safety Information

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this equipment.

• All electrical work must be performed by a qualified, licensed electrician in accordance with national and local electrical codes.
• Ensure the sauna room is properly ventilated.
• Do not place flammable materials on or near the heater.
• Never operate the heater without sauna stones.
• Keep children and pets away from the heater.
• Consult a physician before using a sauna if you have health concerns.

3. Product Overview

The Amerec 9053-407 Pro is a 12KW floor-standing sauna heater designed for commercial and residential use. It operates on a 208V, 3-phase electrical supply and requires an external control unit (not included) for operation. The heater is designed to accommodate Vulcanite sauna rocks for optimal heat distribution.

Image 1: Amerec 9053-407 Pro 12KW Floor Standing Sauna Heater. This image shows the front view of the stainless steel sauna heater, designed for floor installation.

4. Setup and Installation

Installation of this sauna heater requires professional expertise. It must be installed by a qualified electrician and a licensed contractor in accordance with all applicable local and national codes.

4.1 Pre-Installation Checks

• Verify that the electrical supply matches the heater's requirements: 208V, 3-Phase, 33.3 Amp.
• Ensure the sauna room size is within the recommended range of 510 to 740 cubic feet for optimal heating.
• Confirm that a compatible control unit (Elite, Pure 2.0, or SC) is available, as it is not included with the heater.

4.2 Heater Placement

The heater dimensions are approximately 20 inches (W) x 29 inches (H) x 19 inches (D). Ensure adequate clearance from walls and benches as specified in the detailed installation guide provided with the product packaging. The heater must be securely fastened to the floor.

4.3 Electrical Connection

Connect the heater to the dedicated 208V, 3-phase circuit. All wiring must comply with local electrical codes. The control unit must be wired according to its specific instructions and connected to the heater.

4.4 Sauna Rock Installation

The heater includes two 70 lb boxes of Vulcanite rocks. Carefully place the rocks into the heater's rock compartment, ensuring they are loosely packed to allow for proper air circulation. Do not force rocks into the compartment or pack them too tightly, as this can impede airflow and heater performance.

5. Operating Instructions

The Amerec 9053-407 heater is operated via an external control unit (e.g., Elite, Pure 2.0, or SC). Refer to the specific manual for your control unit for detailed operating instructions.

5.1 Initial Start-Up

• After installation, turn on the main power supply to the sauna heater circuit.
• Set the desired temperature and operating time on your external control unit.
• Allow the heater to preheat the sauna room. The initial heating cycle may take longer.

5.2 Regular Operation

• Once the sauna reaches the desired temperature, the heater will cycle on and off to maintain it.
• For steam, carefully ladle small amounts of water onto the hot sauna rocks. Do not pour excessive amounts of water, as this can damage the heating elements.
• Always ensure the sauna room door is closed during operation to maintain heat.

6. Maintenance

Regular maintenance ensures the safe and efficient operation of your Amerec sauna heater.

6.1 Cleaning

• Ensure the heater is completely cool and disconnected from power before cleaning.
• Wipe the exterior of the heater with a damp cloth. Do not use abrasive cleaners or solvents.
• Periodically remove any debris or dust from the rock compartment.

6.2 Sauna Rock Inspection and Replacement

• Inspect the sauna rocks annually, or more frequently with heavy use.
• Replace any rocks that are crumbling, cracked, or have become significantly smaller. Worn rocks can impede airflow and reduce heating efficiency.
• When replacing, ensure new rocks are genuine sauna rocks designed for electric heaters.

7. Troubleshooting

If you encounter issues with your sauna heater, refer to the following common troubleshooting steps. For complex problems, contact a qualified service technician.

• Heater not turning on: Check the main power supply and the circuit breaker. Ensure the external control unit is powered on and set correctly.
• Heater not heating sufficiently: Verify the sauna room size is appropriate for the 12KW heater. Check if the rocks are properly placed and not too tightly packed. Ensure the control unit is set to a high enough temperature.
• Uneven heating: Rearrange the sauna rocks to ensure even distribution and proper airflow.
• Excessive noise: Ensure the heater is securely installed and not vibrating against any surfaces.

If these steps do not resolve the issue, contact Amerec customer support or a certified service technician.

8. Specifications

9. Warranty and Support

For information regarding product warranty, please refer to the warranty card included with your product packaging or visit the official Amerec website. For technical support, replacement parts, or service inquiries, please contact Amerec customer service directly. Ensure you have your model number (9053-407) and purchase date available when contacting support.

Amerec Contact Information: Please refer to the contact details provided on the official Amerec website or in your product documentation.