Realunisence N-SD02-W3
Realunisence Shower Soap Dispenser User Manual
Model: N-SD02-W3
1. Introduction
Thank you for purchasing the Realunisence Wall Mounted 3 Chamber Shower Soap Dispenser. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your product. Please read this manual thoroughly before use.
2. Package Contents
Please verify that all items listed below are included in your package:
- Shower Soap Dispenser (3 Chambers) x 1
- Drill-Free Sticker x 1
- Screw Set x 1
Note: If any items are missing or damaged, please contact Realunisence customer support for assistance.
Image showing the Realunisence 3-chamber shower soap dispenser, along with the included drill-free sticker and screw set, and product dimensions.
3. Product Features
- Premium ABS Material: Environmentally friendly, strong, and wear-resistant construction.
- Large Capacity: Each chamber holds 300ml/10.2fl.oz, reducing the need for frequent refills.
- Visible Window: Allows easy monitoring of liquid levels for timely replenishment.
- Detachable & Refillable Bottles: Wide-opening bottles can be easily removed for cleaning and refilling.
- Precise Nozzle: Dispenses 2cc per press, ensuring no drips, leakage, or plugging.
- Dual Installation Methods: Supports both drill-in and adhesive (drill-free) mounting.
- Labeled Chambers: Clearly marked for Shampoo, Conditioner, and Shower Gel.
Detailed view of the dispenser showcasing its key features and components.
4. Installation Guide
The Realunisence Shower Soap Dispenser offers two installation methods: drill-free adhesive and screw-in. Choose the method best suited for your wall type.
4.1. Drill-Free Adhesive Installation
Tools Required: Dry Cloth
- Step 1: Clean the Wall. Clean the wall surface with a dry cloth. Ensure the surface is smooth and completely dry before proceeding.
- Step 2: Apply Adhesive Sticker. Carefully peel off the backing from the nail-free sticker and firmly stick it onto the desired wall location. Press firmly to remove any air bubbles.
- Step 3: Align and Attach Backplate. Align the holes on the dispenser's backplate with the studs on the adhesive sticker. Press the backplate onto the sticker until it is securely attached.
- Step 4: Assemble Dispenser. Slide the dispenser unit onto the attached backplate. Ensure it clicks securely into place.
- Step 5: Install Bottles. Gently push the square button on the backplane while pushing the shell upwards to remove it. Insert the refillable bottles into the dispenser shell. Align the notches on the backplane with the slits on the shell, then push the shell downwards until it locks.
Visual guide for the adhesive installation process.
Suitable Wall Types for Adhesive Installation:
- Smooth Tile
- Smooth Marble
- Smooth Glass
- Frosted Glass
- Wooden Wall
- Bump Tile
Not Applicable Wall Types for Adhesive Installation:
- Wet Glass
- Plaster Wall
- Cement Wall
- Sticker Wall
Guide to wall surface compatibility for adhesive mounting.
4.2. Screw-in Installation (Drilling Required)
Tools Required: Dry Cloth, Marker, Screwdriver, Drill
- Step 1: Clean the Wall. Clean the wall surface with a dry cloth. Ensure the surface is smooth and dry.
- Step 2: Mark Drilling Positions. Place the dispenser's backplate on the desired installation spot. Use a marker or pencil to mark the locations for drilling holes through the designated screw points on the backplate.
- Step 3: Drill Holes. Use an appropriate drill bit to drill holes at the marked positions.
- Step 4: Install Backplate. Align the holes in the wall with the holes on the backplate. Insert the screws and tighten them securely to fix the backplate to the wall.
- Step 5: Assemble Dispenser. Slide the dispenser unit onto the attached backplate. Ensure it clicks securely into place.
- Step 6: Install Bottles. Gently push the square button on the backplane while pushing the shell upwards to remove it. Insert the refillable bottles into the dispenser shell. Align the notches on the backplane with the slits on the shell, then push the shell downwards until it locks.
Visual guide for the screw-in installation process.
4.3. Installation Video Guide
For a visual demonstration of the installation process, please watch the official Realunisence installation video below:
Official video demonstrating the installation of the Realunisence shower soap dispenser, covering both drill-free and screw-in methods.
5. Operating Instructions
- Filling the Chambers: Open the top lid of the dispenser. Remove the individual bottles from the backplate by gently pushing the square button and lifting the shell upwards. Unscrew the caps of the bottles and fill them with your desired shampoo, conditioner, or body wash. Ensure not to overfill.
- Re-assembling: Place the filled bottles back into the dispenser shell. Align the shell with the backplate and push downwards until it securely locks into place. Close the top lid.
- Dispensing Soap: Press the large button located at the bottom of each chamber to dispense the liquid. A single press dispenses approximately 2cc of product.
- Priming the Pump: If the dispenser is new or has been empty, it may require several presses to prime the pump and start dispensing liquid consistently. Continue pressing until the product flows smoothly.
The dispenser ready for use after filling.
6. Maintenance
- Regular Cleaning: Wipe the exterior of the dispenser with a soft, damp cloth regularly to remove soap residue and water spots. Avoid abrasive cleaners.
- Internal Cleaning: Periodically remove the bottles and rinse them thoroughly with warm water. For a deeper clean, you can use a mild soap solution. Ensure bottles are completely dry before refilling.
- Nozzle Maintenance: If the nozzle becomes clogged, remove the bottle and rinse the nozzle under warm running water. You can also use a small brush to clear any blockages.
- Avoid Harsh Chemicals: Do not use strong acids, alkalis, or corrosive liquids in the dispenser, as this may damage the material and internal components.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Dispenser not dispensing liquid. | Pump not primed; air in the system. Liquid too thick. Nozzle clogged. | Repeatedly press the pump until liquid flows. Dilute thick liquids slightly with water. Clean the nozzle as per maintenance instructions. |
| Liquid leaking from dispenser. | Bottle not properly seated. Damaged seal. | Ensure bottles are correctly inserted and the shell is locked. Contact customer support if a seal is damaged. |
| Dispenser falling off the wall (adhesive method). | Wall surface not clean/dry. Unsuitable wall type. Overloaded dispenser. | Ensure wall is clean and dry before application. Refer to "Suitable Wall Types" section. Do not exceed recommended capacity. Consider screw-in installation for added security. |
8. Specifications
- Brand: Realunisence
- Model Number: N-SD02-W3
- Material: Acrylonitrile Butadiene Styrene (ABS)
- Color: 02tw3 (White/Grey)
- Product Dimensions: 3.74"L x 9.33"W x 8.47"H
- Chamber Capacity: 300ml / 10.2 fl.oz per chamber
- Number of Chambers: 3
- Item Weight: 1.5 pounds
- Installation Type: Wall Mounted (Adhesive or Screw-in)
9. Warranty & Support
Realunisence products are designed for quality and durability. For any questions, concerns, or warranty claims, please contact Realunisence customer support through the retailer's platform or visit the official Realunisence store for more information.
Realunisence Store: Visit Store