KEMIMOTO Motorcycle License Plate Bracket with LED Signal Light for Sportster S RH1250 User Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your KEMIMOTO Motorcycle License Plate Bracket with integrated LED Signal Light. This fender eliminator kit is designed for specific Sportster S RH1250 models (2021-2025) to replace the factory license plate holder and enhance the motorcycle's rear aesthetics and visibility. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Safety Information

• Always ensure the motorcycle is stable and turned off before beginning any installation or maintenance.
• Disconnect the battery before performing any electrical work to prevent short circuits or electrical shock.
• Wear appropriate personal protective equipment, such as gloves and eye protection, during installation.
• Ensure all connections are secure and wires are routed away from moving parts or hot surfaces.
• If you are unsure about any step, consult a qualified motorcycle technician.
• Verify all lights function correctly after installation before riding.

Package Contents

Verify that all components listed below are present in your package:

Image: All parts included in the KEMIMOTO Fender Eliminator Kit.

1. Tail Light x1
2. Rack Holder x1
3. License Plate Bracket x1
4. Extension Plate x1
5. M5 Square Head Bolt x2
6. Bolt x2
7. M5*L12 Cross Head Bolt x2
8. M5 Flange Nut x4
9. Zip Tie x5
10. L Wrench x1

Setup and Installation

This section outlines the steps to install the KEMIMOTO License Plate Bracket. Professional installation is recommended if you are not familiar with motorcycle electrical systems or component removal.

Overview of Installed Product

Image: The KEMIMOTO Fender Eliminator Kit mounted on a motorcycle, showing integrated LED turn signals and brake light.

Image: Visual comparison of the motorcycle's rear fender before and after installation, demonstrating a cleaner appearance.

Installation Steps

1. Prepare the Motorcycle: Park the motorcycle on a stable surface. Turn off the engine and remove the key. Disconnect the negative terminal of the battery to prevent accidental electrical issues.
2. Remove Original Components: Carefully remove the existing license plate holder and any associated wiring. Refer to your motorcycle's service manual for specific instructions on removing the rear fender and tail light assembly.
3. Assemble the Bracket: Attach the tail light to the rack holder, then secure the license plate bracket and extension plate using the provided M5 bolts and nuts. Ensure all connections are snug but do not overtighten.
4. Mount the New Assembly: Position the assembled KEMIMOTO bracket onto the motorcycle's rear fender area. Secure it using the appropriate bolts.
5. Wire the LED Lights: Connect the wiring of the new LED tail light and turn signals to the motorcycle's existing wiring harness. Match the wires according to their functions (e.g., brake, turn signal, ground). Use the provided zip ties to secure any loose wiring.
6. Test Functionality: Reconnect the motorcycle battery. Turn on the ignition and test the brake light, left turn signal, and right turn signal to ensure they are all functioning correctly.
7. Final Check: Ensure all bolts are tightened, and the bracket is securely mounted. Check for any obstructions or loose components.

Installation Video Guide

Operating Instructions

The KEMIMOTO License Plate Bracket features integrated LED lights that serve multiple functions for enhanced visibility and safety.

• Running Light: When the motorcycle's ignition is on, the LED lights will illuminate as a running light, providing continuous rear visibility.
• Brake Light: When the brake lever or pedal is engaged, the LED lights will illuminate brighter to indicate braking.
• Turn Signals: Activating the left or right turn signal switch will cause the corresponding section of the LED light to flash, indicating your intended turn direction.

Maintenance

Regular maintenance ensures the longevity and proper function of your license plate bracket and LED lights.

• Cleaning: Clean the bracket and LED lens regularly with a soft cloth and mild soap solution. Avoid abrasive cleaners that could scratch the surface or damage the LED housing.
• Inspections: Periodically check all mounting bolts for tightness. Vibrations from riding can cause fasteners to loosen over time.
• Wiring: Inspect wiring for any signs of wear, fraying, or damage. Ensure all electrical connections remain secure and free from corrosion.
• LED Functionality: Regularly test the running light, brake light, and turn signals to confirm they are all working correctly.

Troubleshooting

If you encounter issues with your KEMIMOTO License Plate Bracket, refer to the following troubleshooting guide:

Specifications

Image: Key dimensions of the KEMIMOTO license plate bracket.

Warranty and Support

KEMIMOTO products are manufactured to high-quality standards. For warranty information, technical support, or assistance with parts, please refer to the contact information provided with your purchase or visit the official KEMIMOTO website. Keep your purchase receipt as proof of purchase for any warranty claims.