FOGATTI 2.5 Gallon 1440W Electric Mini Tank Water Heater Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your FOGATTI 2.5 Gallon 1440W Electric Mini Tank Water Heater. Please read these instructions thoroughly before installation and use, and retain them for future reference.

2. Important Safety Information

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this equipment.

• Ensure all electrical connections comply with local codes and regulations.
• Do not operate the water heater if it is damaged or malfunctioning.
• Always disconnect power before performing any service or maintenance.
• This appliance must be properly grounded.
• A high-temperature limit device shuts off heat and provides protection when the temperature reaches 167 °F.
• Includes a T&P valve for high water pressure protection.

3. Product Overview and Features

The FOGATTI 2.5 Gallon Electric Mini Tank Water Heater is designed to provide instant hot water for various applications, including under sinks, countertops, RVs, and camping. Its compact design and efficient heating system ensure reliable performance.

Key Features:

• Instant Hot Water: Operates with 1440W power, utilizing an L-shaped heating rod and 310S stainless steel for maximum heat exchange efficiency.
• Long Lifespan: Features a uniform 0.8mm thick German-made enamel layer on the tank surface to prevent corrosion, rust, and leaks. Includes an integrated magnesium rod for tank protection.
• Space-Saving Design: Compact dimensions (13.39"W x 16.5"H x 11.42"D) allow for wall-mounting or placement under sinks and countertops.
• Safety Protection: CSA certified, with a high-temperature limit device (167 °F) and a T&P valve for high water pressure protection. Temperature is adjustable from 55°F to 145°F.
• Easy Installation: Designed for straightforward setup with 1/2" NPT water connections and 120V (AC), 1440W electrical requirements. Includes a plug connection (800mm power cord).

Image 1: FOGATTI 2.5 Gallon Electric Mini Tank Water Heater installed under a sink. This image shows the compact size of the water heater, suitable for under-sink installation.

Image 2: Dimensions of the FOGATTI 2.5 Gallon Electric Mini Tank Water Heater. This image highlights the height, width, and depth of the unit, along with included mounting kit, pressure-relief valve, and drain pipe.

Image 3: Internal construction of the FOGATTI Electric Mini Tank Water Heater, illustrating the 4-layer construction for durability and the L-shaped heating rod.

4. Setup and Installation

Proper installation is crucial for the safe and efficient operation of your water heater. If you are unsure about any steps, consult a qualified plumber or electrician.

4.1 Unpacking and Inspection

• Carefully remove the water heater from its packaging.
• Inspect the unit for any signs of damage. If damage is found, do not proceed with installation and contact customer support.
• Verify that all included components are present: Water Heater x 1, User Manual x 1, T & P Relief Valve x 1.

4.2 Location Requirements

• The water heater can be wall-mounted or floor-mounted.
• Ensure the chosen location is protected from freezing temperatures.
• Provide adequate clearance around the unit for maintenance and air circulation.
• The unit should be installed as close as possible to the point of use to minimize heat loss.

4.3 Plumbing Connections

1. Install the provided T&P (Temperature and Pressure) Relief Valve into the designated opening on the top of the water heater. Ensure to wrap the threads with PTFE tape (more than 15 times) to prevent leaks. Tighten with a wrench.
2. Connect the cold water supply line (blue indicator) to the inlet port of the water heater. Use 1/2" NPT fittings. Wrap threads with PTFE tape (more than 8 times).
3. Connect the hot water outlet line (red indicator) to the outlet port of the water heater. Use 1/2" NPT fittings. Wrap threads with PTFE tape (more than 8 times).
4. Attach a drain tube to the T&P relief valve, directing any discharge to a suitable drain.
5. Important Note: To avoid normal leakage at the inlet and outlet, do not omit the sealing washer at the fitting when connecting the external water hose. External water hose and sealing washer are not included with this product.

4.4 Electrical Connections

• The water heater requires 120 Volts (AC) and 1440 watts.
• It comes with a plug connection (800mm power cord).
• A recommended circuit breaker specification is 15 AMPS for complete electrical safety.
• Ensure the electrical outlet is properly grounded and matches the unit's requirements.

5. Operating Instructions

5.1 Filling the Tank

• Before powering on the unit, ensure the tank is completely filled with water.
• Open a hot water faucet in your home to allow air to escape from the tank.
• Once water flows steadily from the faucet, the tank is full. Close the faucet.

5.2 Adjusting Temperature

• The temperature is adjustable within a range of 55°F to 145°F.
• Locate the temperature control knob on the front of the unit.
• Rotate the knob to your desired temperature setting. The unit will begin heating automatically.
• The heating indicator light will illuminate when the unit is actively heating.

6. Maintenance

Regular maintenance helps ensure the longevity and efficient operation of your water heater.

• Anode Rod Inspection: The integrated magnesium anode rod protects the tank from corrosion. It is recommended to check the anode rod periodically (e.g., every 1-2 years, depending on water hardness) and replace it if significantly depleted.
• Draining the Tank: If the unit will be unused for an extended period or if there is a risk of freezing, drain the tank completely.
• Cleaning: Periodically wipe the exterior of the unit with a soft, damp cloth. Do not use abrasive cleaners.
• T&P Valve Test: Test the T&P relief valve at least once a year by lifting the lever. Water should discharge from the drain pipe. If no water discharges, or if the valve does not reseat properly, replace it immediately.

7. Troubleshooting

8. Specifications

9. Warranty and Support

FOGATTI provides a 6-year limited warranty for the tank and a 1-year warranty for components. This warranty covers defects in materials and workmanship under normal use and service.

For warranty claims or technical support, please refer to the contact information provided in your product packaging or visit the official FOGATTI website.