1. Introduction
This manual provides instructions for the eMylo EMAC913 Wireless Remote Control Switch. This device is a 1-channel 433Mhz RF remote relay switch designed for DC 6V-30V applications, allowing remote control of various electrical devices.
2. Package Contents
- 1 x eMylo Wireless Remote Control Receiver
- 2 x RF Transmitters (Remote Controls)
- 1 x User Manual
3. Specifications
| Feature | Specification |
|---|---|
| Receiver Operating Voltage | DC 6V-30V |
| Channel | 1 |
| RF Frequency | 433Mhz |
| Max Current | 10A |
| Output Type | Passive output |
| Sensitivity | >97dbm |
| Working Temperature | -30℃ to 80℃ |
| Receiver Dimensions | 53 x 36 x 23mm |
| Transmitter Operating Voltage | DC 6V |
| Transmitter Operating Current | ≤15mA |
| Transmitter Quiescent Current | 0mA |
| Transmitter Dimensions | 59 x 34 x 9 mm |
| Remote Range | 20-30m (open area, no interference) |
| Connector Type | Screw |
| Contact Material | Copper |
| Contact Type | Normally Open |
| Mounting Type | Surface Mount |
| Wattage | 120 watts |
The receiver is designed for compact installation, measuring 53 x 36 x 23mm. The remote control measures 59 x 34 x 9mm.
Image: Dimensions of the eMylo Wireless Remote Control Switch receiver and its accompanying remote control.
4. Safety Information
- Ensure power is disconnected before installation or wiring to prevent electric shock.
- This device is designed for DC 6V-30V circuits. Do not connect to AC power unless specified for AC applications.
- Do not exceed the maximum current rating of 10A.
- Keep the device away from water, moisture, and extreme temperatures.
- Installation should be performed by a qualified individual if you are unsure about electrical wiring.
5. Setup and Installation
5.1 Wiring Diagram
The receiver is installed between the power supply and the device you wish to control. Follow the wiring diagram below for proper connection.
Image: Wiring diagram illustrating how to connect the eMylo receiver to a power source and a light fixture. It shows input (N: Neutral line, L: Living line) and output connections.
- Input: Connect the DC 6V-30V power supply to the input terminals (red wire for positive, black wire for negative).
- Output: Connect the device to be controlled (e.g., a light) to the output terminals. The receiver provides a passive output, meaning it acts as a switch for your device's power circuit.
5.2 Pairing the Remote Control (Learning Button)
The receiver has a learning button to pair with the transmitters. Refer to the operating instructions for detailed pairing procedures for different modes.
6. Operating Instructions
The eMylo Wireless Remote Control Switch supports two working modes: Momentary Mode and Toggle Mode. The factory default mode is Toggle Mode.
Image: Diagram illustrating the two operating modes: Momentary Mode (press and hold for ON, release for OFF) and Toggle Mode (press once for ON, press again for OFF).
6.1 Momentary Mode
- To set: Press the learning button on the receiver once. The indicator light will turn on. Then, press the desired button on the remote control. The indicator light will flash and turn off, indicating successful pairing in Momentary Mode.
- Operation: Press and hold the remote button to turn the device ON. Release the button to turn the device OFF.
6.2 Toggle Mode (Factory Default)
- To set: Press the learning button on the receiver twice. The indicator light will turn on. Then, press the desired button on the remote control. The indicator light will flash and turn off, indicating successful pairing in Toggle Mode.
- Operation: Press the remote button once to turn the device ON. Press the same button again to turn the device OFF.
6.3 Clearing Paired Transmitters
To clear all paired transmitters from the receiver's memory, press and hold the learning button on the receiver for approximately 8 seconds until the indicator light flashes rapidly and then turns off. All previously paired remotes will be cleared.
6.4 Remote Control Range
The remote control offers a range of 20-30 meters in an open area without interference. Obstacles such as walls or other electronic devices may reduce the effective range.
7. Maintenance
- Keep the receiver and transmitters clean and dry.
- Avoid exposing the devices to direct sunlight, high humidity, or corrosive environments.
- Replace the battery in the transmitter when the remote range decreases or it stops responding.
8. Troubleshooting
- Device not responding to remote:
- Check if the receiver is properly powered (DC 6V-30V).
- Ensure the device connected to the output is receiving power and is functional.
- Verify the remote control battery is not depleted.
- Re-pair the remote control with the receiver following the instructions in Section 6.
- Reduced remote control range:
- Replace the remote control battery.
- Ensure there are no significant obstructions between the remote and the receiver.
- Minimize interference from other 433Mhz devices.
- Indicator light not working:
- Check the power supply to the receiver.
- If the device is still functional, the indicator light may be faulty, but the switch should still operate.
9. Warranty and Support
eMylo provides a refund and return guarantee for this product. For any questions or technical assistance, please contact eMylo customer service. They offer 24-hour customer support to address your concerns.
For more information or to contact support, please visit the official eMylo store on Amazon: eMylo Amazon Store
