IKEA 002.404.63

STOCKARYD Wood Treatment Oil User Manual

Model: 002.404.63 | Brand: IKEA

Introduction

This manual provides comprehensive instructions for the safe and effective use of STOCKARYD Wood Treatment Oil. This product is designed for treating indoor wooden surfaces, enhancing their durability and appearance. Please read this manual thoroughly before use to ensure proper application and maintenance.

Safety Information

WARNING: Flammable liquid and vapor. May cause drowsiness or dizziness. Keep out of reach of children.

  • Ensure adequate ventilation during application and drying. Work in a well-ventilated area or outdoors.
  • Avoid contact with skin and eyes. Wear protective gloves and eye protection. In case of contact, rinse immediately with plenty of water and seek medical advice.
  • Do not ingest. If swallowed, do not induce vomiting. Seek immediate medical attention.
  • Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking.
  • Dispose of contents/container in accordance with local regulations. Rags, sanding dust, and other waste soaked with the product may self-ignite. Soak them in water or place them in a sealed metal container before disposal.

Setup and Preparation

Proper preparation of the wooden surface is crucial for optimal results.

  1. Clean the Surface: Ensure the wooden surface is clean, dry, and free from dust, dirt, grease, or old finishes. Use a mild detergent if necessary, and allow the wood to dry completely.
  2. Sand if Necessary: For untreated or previously treated surfaces with imperfections, lightly sand the wood in the direction of the grain using fine-grit sandpaper (e.g., 180-220 grit). This helps the oil penetrate evenly. Remove all sanding dust thoroughly.
  3. Shake the Can: Before opening, shake the STOCKARYD Wood Treatment Oil can thoroughly to ensure the contents are well mixed.
  4. Test Area: Always test the oil on an inconspicuous area of the wood first to check the color and finish.

Application Instructions

Follow these steps for applying STOCKARYD Wood Treatment Oil:

  1. Apply the Oil: Apply a thin, even coat of oil using a brush or a clean cloth. Work in the direction of the wood grain.
  2. Allow Penetration: Let the oil penetrate the wood for approximately 15-20 minutes. The wood should absorb the oil.
  3. Wipe Off Excess: After the penetration time, wipe off any excess oil with a clean, lint-free cloth. Ensure no sticky residue remains on the surface. If excess oil is not removed, the surface may become sticky.
  4. Drying Time: Allow the surface to dry for approximately 4-6 hours before light use. The drying time may vary depending on temperature, humidity, and the amount of oil applied.
  5. Second Coat (Optional): For increased durability or a deeper finish, a second coat can be applied after the first coat has fully dried. Repeat steps 1-4.
STOCKARYD Wood Treatment Oil can, 500 ml

Image of the STOCKARYD Wood Treatment Oil can, showing the product name, volume (500 ml), and an illustration of a treated wooden surface. The label also indicates a coverage of 14-18 m² per 500 ml and a drying time of 4-6 hours.

Coverage: One 500 ml can of STOCKARYD Wood Treatment Oil covers approximately 14-18 square meters (150-194 sq ft) depending on the wood type and porosity.

Maintenance and Care

To maintain the treated wooden surfaces:

  • Regular Cleaning: Clean treated surfaces with a damp cloth and a mild detergent. Avoid abrasive cleaners or harsh chemicals.
  • Reapplication: Reapply STOCKARYD Wood Treatment Oil as needed, typically once or twice a year, or when the wood starts to look dry or worn. Follow the application instructions for reapplication.
  • Spills: Wipe up spills immediately to prevent staining.

Troubleshooting

ProblemPossible CauseSolution
Surface feels sticky after drying.Excess oil was not wiped off.Wipe the surface thoroughly with a clean, lint-free cloth. If still sticky, lightly sand the area and reapply a very thin coat, ensuring all excess is removed.
Uneven finish or blotches.Uneven application or insufficient surface preparation.Ensure the surface is clean and evenly sanded. Apply the oil thinly and evenly, wiping off all excess. For existing blotches, lightly sand the area and reapply.
Oil not penetrating the wood.Surface not clean or previously treated with a sealant.Ensure the wood is clean and dry. If a previous sealant is present, it may need to be removed by sanding before oil can penetrate.

Specifications

  • Brand: IKEA
  • Model Number: 002.404.63
  • Recommended Use: Indoor wood surfaces
  • Volume: 500 ml
  • Coverage: Approximately 14-18 m² per 500 ml
  • Drying Time: 4-6 hours (approximate)
  • ASIN: B0BDL1915J
  • First Available Date: April 28, 2023

Warranty and Support

For information regarding warranty, returns, or product support, please refer to the purchase documentation or contact IKEA customer service directly. Keep your proof of purchase for any warranty claims.

For further assistance, visit the official IKEA website or contact their support channels.

© 2023 IKEA. All rights reserved.