1. Introduction
This manual provides essential information for the proper installation, care, and maintenance of your Hostile H129 Mojave Custom Wheel. Please read these instructions thoroughly before proceeding with installation or use to ensure safety and optimal performance.
The Hostile H129 Mojave wheel is designed for specific vehicle applications. Verify that the wheel specifications match your vehicle's requirements before installation.
2. Safety Information
Always prioritize safety when working with vehicle components. Improper installation or maintenance can lead to serious injury or vehicle damage.
- Consult a qualified automotive technician if you are unsure about any installation steps.
- Use appropriate safety gear, including gloves and eye protection.
- Ensure the vehicle is securely supported on jack stands before removing or installing wheels.
- Never exceed the maximum load rating of the wheel or tire.
- Regularly inspect wheels for damage, cracks, or signs of wear.
3. Installation
Proper installation is critical for the performance and safety of your custom wheels. Lug nuts are not included with this wheel and must be purchased separately, ensuring they are compatible with your vehicle and the wheel's lug seat type.
3.1 Pre-Installation Check
- Verify Fitment: Before mounting tires, perform a test fit of the wheel on the vehicle's hub to ensure proper clearance with brake calipers, suspension components, and fender wells.
- Inspect Wheels: Carefully inspect each wheel for any shipping damage or manufacturing defects. Do not install damaged wheels.
- Lug Nut Compatibility: Confirm that your lug nuts are the correct thread pitch, seat type (e.g., conical, spherical, flat), and length for both your vehicle and the new wheels.
3.2 Mounting Tires
Tire mounting should be performed by a professional using appropriate equipment to avoid damage to the wheel or tire.
- Use only approved tire mounting lubricants.
- Ensure the tire bead is properly seated on the wheel.
- Balance the wheel and tire assembly after mounting to prevent vibrations.
3.3 Wheel Installation on Vehicle
- Prepare Vehicle: Park the vehicle on a level surface, engage the parking brake, and loosen lug nuts on the wheel to be replaced. Jack up the vehicle and secure it with jack stands.
- Remove Old Wheel: Remove the lug nuts and carefully take off the old wheel.
- Clean Hub Surface: Clean any rust, dirt, or debris from the vehicle's hub mounting surface to ensure the new wheel sits flush.
- Install New Wheel: Carefully place the new Hostile H129 Mojave wheel onto the hub. Ensure it is fully seated against the mounting surface.
- Install Lug Nuts: Hand-tighten the lug nuts in a star pattern until they are snug.
- Lower Vehicle: Lower the vehicle until the tire just touches the ground, but the full weight is not on the wheel.
- Torque Lug Nuts: Using a torque wrench, tighten the lug nuts to the vehicle manufacturer's specified torque settings in a star pattern. Do not use an impact wrench for final tightening.
- Final Lowering: Fully lower the vehicle and remove jack stands.
- Re-torque Check: After driving approximately 50-100 miles, re-check the lug nut torque to ensure they remain properly tightened.
Figure 1: Front view of the Hostile H129 Mojave Custom Wheel. This image displays the intricate spoke design and the Hostile branding on the rim and center cap.
Figure 2: Angled view of the Hostile H129 Mojave Custom Wheel, highlighting the depth and finish of the asphalt rim.
4. Maintenance
Regular maintenance will help preserve the appearance and integrity of your Hostile H129 Mojave wheels.
- Cleaning: Clean wheels regularly with mild soap and water. Avoid harsh chemicals, abrasive cleaners, or stiff brushes, which can damage the finish. Rinse thoroughly and dry with a soft cloth to prevent water spots.
- Inspection: Periodically inspect wheels for any signs of damage, such as bends, cracks, or deep scratches. Address any damage promptly to prevent further issues.
- Tire Pressure: Maintain correct tire pressure as specified by your vehicle manufacturer. Incorrect tire pressure can affect handling, tire wear, and wheel integrity.
- Wheel Balancing: If you experience vibrations, have your wheels re-balanced by a professional.
5. Troubleshooting
This section addresses common issues that may arise with custom wheels.
| Issue | Possible Cause | Solution |
|---|---|---|
| Vibrations at speed | Unbalanced wheels, bent rim, loose lug nuts, improper tire pressure. | Have wheels professionally balanced. Inspect for damage. Re-torque lug nuts. Check tire pressure. |
| Uneven tire wear | Improper tire pressure, misalignment, unbalanced wheels. | Check tire pressure. Have vehicle alignment checked. Have wheels balanced. |
| Wheel finish fading/peeling | Exposure to harsh chemicals, abrasive cleaning, environmental factors. | Use only mild soap and water for cleaning. Avoid automatic car washes with harsh brushes. |
6. Specifications
Key technical specifications for the Hostile H129 Mojave Custom Wheel:
- Model: H129 Mojave
- Manufacturer Part Number: H129-2090613550A
- Size: 20x9 inches
- Offset: 1 Millimeter
- Bolt Pattern: 6x135 (6 holes, 135mm Pitch Circle Diameter)
- Hub Bore: 87mm
- Finish: Asphalt (Satin Black)
- Item Weight: Approximately 41.9 Pounds
- UPC: 842213148762
- Brand: HOSTILE
- Manufacturer: MKW Alloy
7. Warranty Information
Hostile wheels typically come with a manufacturer's warranty covering defects in material and workmanship. The specific terms and duration of the warranty may vary. Please refer to the official Hostile Wheels website or contact your authorized dealer for detailed warranty information and registration procedures.
Note: Damage caused by improper installation, neglect, accident, or unauthorized modification is generally not covered under warranty.
8. Customer Support
For technical assistance, warranty claims, or general inquiries regarding your Hostile H129 Mojave Custom Wheel, please contact your point of purchase or visit the official Hostile Wheels website for contact information.
When contacting support, please have your wheel model (H129 Mojave) and manufacturer part number (H129-2090613550A) readily available.