1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your Anyqinsog 6-Pin Power Cable Loom and 4-Pin Speaker Input Harness. This product is designed to provide a reliable wiring solution for specific Pioneer TS-WX series models, ensuring proper power and speaker signal connections. Please read this manual thoroughly before installation to ensure safe and correct usage.
2. Product Overview
The Anyqinsog cable loom and harness kit is a replacement or repair component for car audio systems. It features a 6-pin connector for power and ground, and a 4-pin connector for speaker input signals. The wires are pre-crimped and ready for connection to compatible Pioneer subwoofers or amplifiers.
Image 2.1: Overview of the 6-pin power cable loom and 4-pin speaker input harness.
2.1 Key Features
- 100% new kit with quality crimped joints.
- Designed for auto stereo repair and replacement.
- Compatible with Pioneer models: TS-WX20LPA, TS-WX205A, TS-WX206A, TS-WX44A, TS-WX33A, TS-WX22A, TS-WX707A.
- Wire types: UL1015 16AWG for power and ground, UL1007 18AWG for remote and speaker input wires.
- Cable length: Approximately 15cm.
2.2 Package Contents
- 1 x 6-pin power harness
- 1 x 4-pin speaker input harness
3. Setup and Installation
3.1 Before You Begin
- Safety First: Always disconnect the vehicle's battery negative terminal before performing any electrical work to prevent short circuits and electrical shock.
- Compatibility Check: Ensure that your Pioneer model is listed as compatible with this harness. Refer to the 'Product Overview' section for compatible models.
- Tools Required: You may need basic wiring tools such as wire strippers, crimpers (if modifying connections), electrical tape, and zip ties for securing cables.
- Identify Wires: Familiarize yourself with the wire colors and their functions as described in the specifications.
Image 3.1: The power and speaker input harnesses laid out, showing their respective connectors and wire colors.
3.2 Installation Steps
- Locate the Existing Harness: Identify the corresponding power and speaker input ports on your Pioneer TS-WX series unit. These are typically located on the back or side of the unit.
- Disconnect Old Harness (if applicable): If replacing an existing harness, carefully disconnect it from the Pioneer unit. Do not pull on the wires; grasp the connector firmly.
- Connect the 6-Pin Power Harness: Align the 6-pin connector of the new harness with the power input port on your Pioneer unit. Gently push until it clicks securely into place. Ensure the connection is firm and there is no wobble.
Image 3.2: Detailed view of the 6-pin (top) and 4-pin (bottom) connectors, showing their pin configurations.
- Connect the 4-Pin Speaker Input Harness: Similarly, align the 4-pin connector with the speaker input port on your Pioneer unit and push until it is securely connected.
- Wire Connections: Connect the free ends of the harness wires to your vehicle's power source, ground, remote turn-on, and speaker outputs. Refer to the wiring diagram of your Pioneer unit and vehicle for specific connections.
- UL1015 16AWG: Typically used for power (red/yellow) and ground (black). Note that red wire can replace yellow for power.
- UL1007 18AWG: Used for remote turn-on and speaker input wires.
Image 3.3: Close-up of a single crimped wire terminal, demonstrating the quality of the connection.
Image 3.4: Detailed view of multiple crimped wire terminals, showing the secure and professional finish.
- Secure Wiring: Use zip ties or electrical tape to neatly bundle and secure the wires, preventing them from interfering with moving parts or being pinched.
- Reconnect Battery: Once all connections are secure and verified, reconnect the vehicle's battery negative terminal.
- Test System: Turn on your vehicle's audio system and test the functionality of the Pioneer unit to ensure proper operation.
4. Operation
The 6-pin power cable loom and 4-pin speaker input harness are passive components designed to facilitate electrical connections. Once properly installed, their operation is integrated with the functionality of the connected Pioneer TS-WX series unit and your vehicle's audio system. There are no user-operable controls on the harness itself.
5. Maintenance
This product requires minimal maintenance. To ensure longevity and reliable performance:
- Keep Connections Clean: Periodically inspect the connections for any signs of corrosion or debris. If necessary, gently clean the connector pins with a non-conductive cleaner.
- Avoid Strain: Ensure that the cables are not under excessive tension or bent at sharp angles, which can damage the internal wiring or connectors.
- Secure Wiring: Regularly check that the cables remain securely fastened and are not loose or rubbing against sharp edges.
- Environmental Protection: While designed for automotive use, avoid exposing the harness to extreme moisture or temperatures beyond typical vehicle operating conditions.
6. Troubleshooting
If you experience issues after installing the harness, consider the following common troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Pioneer unit does not power on. | Loose power connection, incorrect wiring, blown fuse. | Check the 6-pin power harness connection to the unit. Verify power and ground wires are correctly connected to the vehicle's electrical system. Check vehicle's fuse box for blown fuses. |
| No sound from speakers. | Loose speaker input connection, incorrect speaker wiring. | Ensure the 4-pin speaker input harness is securely connected. Verify speaker wires are correctly connected to the vehicle's speaker outputs. Check speaker polarity. |
| Intermittent power or sound. | Loose connections, damaged wire. | Inspect all connections for tightness. Check wires for any signs of fraying or damage. Re-secure any loose wires. |
| Harness does not fit the Pioneer unit. | Incompatible model. | Double-check your Pioneer unit's model number against the compatibility list in this manual. Ensure you are attempting to connect the correct harness to the correct port. |
7. Technical Specifications
| Specification | Detail |
|---|---|
| Product Name | 6-Pin Power Cable Loom and 4-Pin Speaker Input Harness |
| Brand | Anyqinsog |
| Model Number | 6pTS-WX20LPA |
| Compatible Pioneer Models | TS-WX20LPA, TS-WX205A, TS-WX206A, TS-WX44A, TS-WX33A, TS-WX22A, TS-WX707A |
| Wire Type (Power/Ground) | UL1015 16AWG |
| Wire Type (Remote/Speaker) | UL1007 18AWG |
| Cable Length | Approx. 15 cm (5.9 inches) |
| Connector Type (Power) | 6-pin Circular |
| Connector Type (Speaker) | 4-pin Rectangular |
| Material | Polycarbonate (PC) |
| Item Weight | 1.41 ounces |
| Package Dimensions | 5.91 x 5.12 x 0.79 inches |
8. Warranty Information
Specific warranty details for this product are typically provided at the point of purchase or on the product packaging. Please retain your proof of purchase for any warranty claims. For information regarding returns or replacements, refer to the retailer's policy where the product was acquired.
9. Customer Support
For further assistance or inquiries regarding the Anyqinsog 6-Pin Power Cable Loom and 4-Pin Speaker Input Harness, please contact the seller or manufacturer through the platform where the product was purchased. Provide your order details and a clear description of your issue for prompt support.