1. Introduction
This manual provides essential information for the safe and effective use of your new high-pressure washer hose. Please read it thoroughly before initial use and retain it for future reference. This hose is designed for use with various compatible pressure washer models, offering a durable and efficient solution for your cleaning needs.
Figure 1: The 20-meter high pressure washer hose, neatly coiled, showcasing its overall length and black color.
2. Compatibility
This high-pressure washer hose is designed to be compatible with a range of pressure washer brands and models. Please verify your pressure washer's connection type before purchase and installation.
- Compatible with INALSA Pressure Washer
- Compatible with RESQTECH Pressure Washer PW-101 ONLY
- Compatible with GERNI Pressure Washer
- Compatible with STIHL RE-80
- Compatible with LIFELONG Pressure Washer
- Compatible with BLACK DECKER Pressure Washer (Old Model)
- Compatible with HIKOKI Pressure Washer
3. Setup and Installation
Follow these steps to properly connect your high-pressure washer hose:
- Inspect Connections: Before connecting, ensure both ends of the hose and the corresponding ports on your pressure washer and spray gun are clean and free of debris. Check for any damage to the threads or O-rings.
- Connect to Pressure Washer: Identify the threaded end of the hose. Screw this end securely onto the high-pressure outlet of your pressure washer. Hand-tighten first, then use a wrench if necessary, but do not overtighten to avoid damaging the threads.
- Connect to Spray Gun/Accessory: Identify the quick-connect style fitting on the other end of the hose. Insert this fitting into the inlet of your spray gun or other high-pressure accessory until it clicks securely into place. Pull gently to ensure it is locked.
- Check for Leaks: Once connected, turn on the water supply to the pressure washer and briefly activate the pressure washer to check for any leaks at the connection points. Tighten connections if necessary.
Figure 2: Detailed view of the brass threaded connector for pressure washer attachment.
Figure 3: Detailed view of the quick-connect style fitting for spray gun attachment.
4. Operating Instructions
To ensure safe and effective operation of your high-pressure washer hose, observe the following guidelines:
- Uncoil Completely: Always uncoil the hose completely before use to prevent kinks, tangles, and potential damage to the hose or reduction in water flow.
- Avoid Sharp Bends: Do not bend the hose sharply or run it over sharp edges, as this can weaken the hose material and lead to leaks or bursts.
- Protect from Traffic: Keep the hose away from vehicle traffic or areas where it might be stepped on or run over, which could cause damage.
- Maintain Distance: When operating the pressure washer, maintain a safe distance from the hose to avoid accidental contact with high-pressure water streams.
- Pressure Limits: Do not exceed the maximum pressure rating of 220 Bars for this hose. Operating beyond this limit can cause hose failure and injury.
5. Maintenance
Proper maintenance will extend the life of your high-pressure washer hose:
- Cleaning: After each use, rinse the hose with clean water to remove any dirt, chemicals, or debris.
- Draining: Ensure all water is drained from the hose before storage, especially in freezing temperatures, to prevent ice formation and damage.
- Coiling: Coil the hose neatly for storage. Avoid tight coiling or kinking.
- Storage: Store the hose in a cool, dry place, away from direct sunlight, extreme temperatures, and corrosive chemicals.
- Regular Inspection: Periodically inspect the entire length of the hose for cuts, abrasions, bulges, or other signs of wear and tear. Check the connectors for corrosion or damage. Replace the hose immediately if any damage is found.
6. Troubleshooting
This section addresses common issues you might encounter with your high-pressure washer hose.
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaking from connections | Loose connection, damaged O-ring, or worn threads. | Ensure connections are tightened securely. Inspect and replace O-rings if damaged. Check threads for wear. |
| Reduced water pressure | Hose kinked, internal blockage, or hose damage. | Straighten any kinks in the hose. Disconnect and check for blockages. Inspect hose for internal damage or bulges. |
| Hose burst or visible damage | Exceeded maximum pressure, physical damage, or material fatigue. | Immediately discontinue use. The hose must be replaced. Do not attempt to repair a damaged high-pressure hose. |
7. Specifications
Key technical specifications for the High Pressure Washer Hose:
| Attribute | Value |
|---|---|
| Model Number | M22XA_20 |
| Brand | Generic |
| Material | Nylon+PVC+FIBER+BRASS |
| Colour | Black |
| Length | 20 Meters |
| Item Weight | 999 Grams |
| Maximum Pressure | 220 Bars |
| Outside Diameter | 12 Millimetres |
| Special Features | Lightweight |
| Country of Origin | India |
8. Warranty Information
Specific warranty details for this product may vary. Please refer to the product packaging or contact the manufacturer directly for information regarding warranty coverage, terms, and conditions.
9. Customer Support
For any questions, technical assistance, or support regarding your high-pressure washer hose, please contact the manufacturer:
Manufacturer: Washers Hose INDIA
Contact Number: 7990846445