1. Introduction
This manual provides essential instructions for the safe and efficient operation of your Voxelab Aquila Pro 3D Printer. Please read this manual thoroughly before operating the device to ensure proper usage and to prevent damage.
The Voxelab Aquila Pro is an FDM (Fused Deposition Modeling) 3D printer designed for reliable and high-quality 3D printing. Key features include an auto-leveling system, a Carborundum glass platform, dual Z-axis for stability, a filament detector, and resume printing functionality.
Figure 1.1: Voxelab Aquila Pro 3D Printer, showcasing its overall design.
2. Setup and Assembly
The Voxelab Aquila Pro is designed for quick and easy assembly. Follow these steps to set up your printer:
- Install Z-axis Frame: Securely attach the Z-axis frame to the base of the printer.
- Install Screen: Connect and mount the touchscreen display to the designated port.
- Install Nozzle: Attach the print nozzle assembly to the extruder carriage.
- Install Filament Rack: Mount the filament spool holder at the top of the printer.
Figure 2.1: Assembly steps for the Aquila Pro, illustrating the quick setup process.
After physical assembly, ensure all cables are securely connected according to the included wiring diagram.
3. Operation
3.1 Power On and Initial Checks
Connect the power cable and turn on the printer. The 4.3-inch touchscreen will display the main interface.
Figure 3.1: The 4.3-inch touchscreen interface provides user-friendly control and real-time print status.
3.2 Auto Leveling System
The Aquila Pro features an upgraded auto-leveling system. This system performs smart leveling and allows for auxiliary fine-tuning by hand to ensure accurate calibration and optimal first layer adhesion.
Figure 3.2: The auto-leveling system ensures precise bed calibration for consistent print quality.
3.3 Loading Filament
Insert the filament into the filament detector and feed it into the extruder until it emerges from the nozzle. Ensure the filament is properly seated to avoid printing issues.
3.4 Starting a Print
Transfer your 3D model file (STL format supported) to the printer via USB stick or WiFi connection. Select the desired file from the touchscreen interface and initiate the print. The printer will preheat the nozzle and bed before starting.
3.5 Dual Z-axis Stability
The dual Z-axis rails provide enhanced stability during printing, contributing to smoother movement and improved print quality, especially for taller objects.
Figure 3.3: Dual Z-axis rails provide stability for precise vertical movement during printing.
3.6 Carborundum Glass Platform
The Carborundum glass platform offers excellent adhesion for prints during operation and easy removal once cooled. Ensure the platform is clean before each print.
3.7 Filament Detector and Resume Printing
The integrated filament detector pauses printing if the filament runs out, allowing you to load new filament and resume the print. The resume printing function also allows the printer to continue a print after a power outage.
4. Maintenance
Regular maintenance ensures the longevity and optimal performance of your Voxelab Aquila Pro 3D Printer.
- Clean the Print Platform: Regularly clean the Carborundum glass platform with isopropyl alcohol to ensure good adhesion.
- Inspect Nozzle: Check the nozzle for clogs or wear. Replace if necessary.
- Lubricate Moving Parts: Apply a small amount of lubricant to the Z-axis lead screws and other moving parts periodically.
- Firmware Updates: Check the official Voxelab website for any available firmware updates to improve performance and add features.
5. Troubleshooting
This section addresses common issues you might encounter with your Aquila Pro 3D Printer.
| Problem | Possible Cause | Solution |
|---|---|---|
| Print not sticking to bed | Bed not level, bed temperature too low, dirty print surface, incorrect Z-offset. | Perform auto-leveling, clean the Carborundum glass platform, adjust bed temperature, calibrate Z-offset. |
| Filament not extruding | Clogged nozzle, tangled filament, incorrect temperature, faulty extruder. | Clear nozzle clog, ensure filament spool unwinds freely, verify print temperature settings, check extruder mechanism. |
| Poor print quality (layer shifts, stringing) | Loose belts, unstable frame, incorrect print speed or retraction settings. | Check and tighten belts, ensure printer is on a stable surface, adjust print speed and retraction in slicing software. |
| WiFi connection issues | Incorrect network settings, router interference, outdated firmware. | Verify WiFi credentials, ensure printer is within range, try connecting to a 2.4GHz network, update firmware via USB if necessary. |
6. Specifications
Below are the technical specifications for the Voxelab Aquila Pro 3D Printer:
- Model: Aquila-pro
- Brand: Voxelab
- Product Dimensions: 9.25 x 9.25 x 9.84 inches
- Build Volume: 235 x 235 x 250 mm
- Item Weight: 27.7 pounds
- Material: Carborundum (for print platform)
- Color: Black
- Compatible Devices: Laptop, Smartphone (for control/monitoring)
- Supported File Format: STL
- Key Features: Auto Leveling, Dual Z-axis, Filament Detector, Resume Printing, 4.3-inch Touchscreen, WiFi Connectivity
Figure 6.1: The Aquila Pro offers a generous build volume of 235x235x250mm.
Figure 6.2: Feature comparison between Aquila and Aquila Pro models, showing the enhanced capabilities of the Pro version.
7. Warranty and Support
For technical assistance, warranty claims, or further inquiries, please contact Voxelab customer support. Refer to the official Voxelab website or the product packaging for the most current contact information and warranty details.
Online Resources:
- Official Voxelab Website: www.voxelab3dp.com
- Product Support Page: Check the Voxelab website for a dedicated support page for the Aquila Pro model.
Always ensure you have your product model number (Aquila-pro) and purchase date available when contacting support.
