Introduction
Thank you for choosing the NERDON 12-Inch Brushed Nickel Ceiling Mounted Shower System. This manual provides essential information for the safe and correct installation, operation, and maintenance of your new shower system. Please read these instructions thoroughly before installation and retain them for future reference.
Figure 1: Complete NERDON Shower System Overview
Safety Information
- Always turn off the main water supply before beginning any installation or maintenance.
- Ensure all plumbing connections are secure to prevent leaks.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves during installation.
- This shower system is designed for standard residential plumbing. Do not modify the product.
Package Contents
Verify that all components listed below are present and undamaged before proceeding with installation.
Figure 2: Included Components
- 12-inch Brushed Nickel Ceiling Shower Head (Brass)
- Rainfall Shower Head with Handheld (Brass)
- 11.8-inch Shower Arm (Stainless Steel)
- 59-inch Shower Hose (Stainless Steel)
- Handheld Shower Holder (Stainless Steel)
- Shower Valve (Brass) and Trim Kit
- Plumber's Tape
- Hardware Pack (screws, anchors, etc.)
Setup and Installation
Professional installation is recommended. Follow these general steps for installation. Refer to local plumbing codes.
1. Rough-in Valve Installation
- Turn off the main water supply.
- Prepare the wall opening for the rough-in valve body.
- Connect the hot and cold water lines to the designated inlets on the brass valve body (NPT 1/2").
- Connect the fixed shower head connector (NPT 1/2") and handheld shower head connector (NPT 1/2") to the valve body.
- Secure the valve body within the wall, ensuring it is level and at the correct depth for the trim kit.
- Perform a leak test before closing the wall.
Figure 3: Rough-in Valve Body Connections
Figure 4: Pressure Balance Valve Features
2. Ceiling Mounted Shower Head and Arm Installation
- Thread the 11.8-inch shower arm into the ceiling connection. Ensure it is securely tightened and sealed with plumber's tape.
- Attach the 12-inch rain shower head to the shower arm. The shower head features a 360-degree adjustable angle connector for optimal positioning.
Figure 5: Rain Shower Head Features
3. Handheld Shower and Holder Installation
- Install the square shower bracket holder onto the wall, connecting it to the handheld shower head connector from the rough-in valve.
- Connect one end of the 59-inch stainless steel shower hose to the handheld shower head and the other end to the shower bracket holder.
- Place the brass handheld shower head into the holder. The holder is 360-degree adjustable.
Figure 6: Handheld Shower Head and Hose
Important Installation Note:
Figure 7: Tub Spout Compatibility Warning
This two-function shower valve is not designed for installation with a tub spout. Attempting to connect a tub spout may result in improper function or damage.
Operating Instructions
The NERDON shower system features a single handle for temperature control and a diverter knob for switching between the rain shower head and the handheld shower head.
Figure 8: Two-Function Shower System Control
- Temperature Control: Rotate the main handle to adjust the water temperature. The pressure balance valve maintains consistent temperature, preventing sudden changes.
- Function Selection: Use the small knob on the trim plate to switch between the 12-inch rain shower head and the handheld shower head.
Maintenance
- Cleaning: Clean the shower heads and trim with a soft cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the brushed nickel finish.
- Silicone Nozzles: The rain shower head and handheld shower head feature easy-clean silicone nozzles. Periodically rub the nozzles to dislodge any mineral buildup and maintain optimal spray performance.
- Regular Inspection: Periodically check all connections for leaks and ensure the shower hose is free from kinks or damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Low water pressure | Mineral buildup in nozzles; partially closed water supply valve. | Clean silicone nozzles; ensure main water supply valve is fully open. |
| Water leaks from connections | Loose connections; worn out plumber's tape. | Tighten connections; reapply plumber's tape. |
| Inconsistent water temperature | Pressure balance valve issue (rare); hot/cold water supply problems. | Verify hot and cold water supply; if issue persists, contact support. |
| Diverter not switching properly | Debris in valve; worn diverter cartridge. | Flush the system; if issue persists, contact support. |
Specifications
| Brand | NERDON |
| Model Number | 12 inch Ceiling Mounted Shower System |
| Color | Brushed Nickel |
| Material | Brass, Stainless Steel |
| Finish Type | Brushed |
| Number of Handles | 1 |
| Mounting Type | Ceiling Mount |
| Head Size | 12 inches |
| Item Weight | 10.45 pounds (4.75 Kilograms) |
| Product Dimensions | 16.54 x 5.91 x 12.68 inches |
| UPC | 638457102697 |
Warranty and Support
Warranty: This product comes with a Ten-year Warranty from the date of purchase. Please ensure the user manual is read carefully before installation and that the product is installed correctly to ensure warranty validity.
Customer Support: If you encounter any problems with your NERDON shower system, please do not hesitate to contact our customer service team. They are available to provide assistance and support.
(Specific contact information, such as email or phone number, would typically be provided here by the manufacturer.)