1. Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your RIVECO 22U Open Frame Server Rack. Please read this manual thoroughly before installation and use to ensure proper setup and safe operation. Keep this manual for future reference.
2. Safety Information
- Always ensure the rack is placed on a stable, level surface.
- Distribute equipment weight evenly to prevent tipping.
- Do not exceed the maximum load capacity: 600 lbs with leveling feet, 500 lbs with casters.
- Use appropriate tools for assembly and ensure all fasteners are securely tightened.
- Keep children and pets away from the rack during assembly and operation.
- Exercise caution when moving the rack, especially when loaded. Engage brake casters when stationary.
- Ensure proper grounding for all electrical equipment mounted in the rack.
3. Package Contents
Verify that all components listed below are present in your package:
- RIVECO 22U Open Frame Server Rack components
- All relevant assembly screws & nuts (M6 screws for assembly, M6 screws for equipment mounting)
- 4x Leveling feet
- 2x Casters without brake, 2x Casters with brake
- 16x Caster screws
- 1x Torque wrench
- 2x High quality vented universal rack shelves
- 1x PDU (Power Distribution Unit) with 8 outlets and surge protector
4. Assembly Instructions
Follow these steps to assemble your RIVECO 22U Open Frame Server Rack. It is recommended to have a second person assist with assembly.
4.1. Rack Frame Assembly
- Install Vertical Posts: Secure the four vertical posts to the bottom frame using the provided M6 screws. Ensure the numbered sides of the posts face outwards for easy unit counting.
- Install Top Frame: Attach the top frame to the four vertical posts, aligning the holes and securing with M6 screws.
- Install Casters or Leveling Feet:
- For Casters: Flip the assembled frame upside down. Attach the four casters (2 with brakes, 2 without) to the bottom frame using the caster screws. Ensure the brake casters are positioned on the front side for easy access.
- For Leveling Feet: If mobility is not required, install the four leveling feet into the designated holes on the bottom frame. Adjust them to ensure stability.
4.2. Installing Shelves and PDU
- Install Rack Shelves: Align the vented universal rack shelves with the desired vertical post holes. Secure them using the provided screws and cage nuts. The shelves can be adjusted to various heights.
- Install PDU: Align the PDU (Power Distribution Unit) with the posts' holes. Secure it using screws and cage nuts. Ensure the PDU is easily accessible for power connections.
4.3. Assembly Video Guide
For a visual guide on the assembly process, please refer to the following video:
5. Operating Instructions
5.1. Mounting Equipment
The RIVECO 22U Open Frame Server Rack is designed for 19-inch standard equipment. It features both square holes for IT equipment and round holes for audio/video (AV) gear.
- Align your rack-mountable devices with the appropriate holes on the vertical posts.
- Use the provided M6 equipment mounting screws and cage nuts to secure your devices.
- Ensure devices are securely fastened before releasing them.
- For non-19-inch devices, utilize the provided rack shelves.
5.2. Cable Management
Proper cable management is crucial for airflow and ease of maintenance.
- Route cables neatly along the sides of the rack or through designated cable management rings (if included or purchased separately).
- Use cable ties or Velcro straps to bundle cables, avoiding excessive tension.
- Ensure cables do not obstruct airflow or access to equipment.
6. Maintenance
- Regularly inspect all screws and nuts for tightness and re-tighten if necessary.
- Clean the rack periodically with a soft, dry cloth to remove dust and debris. Avoid abrasive cleaners.
- Check casters and leveling feet for wear and tear. Replace if damaged.
- Ensure proper ventilation around the rack to prevent overheating of equipment.
7. Troubleshooting
- Rack is wobbly: Ensure all screws are tightened. If using leveling feet, adjust them to stabilize the rack. If using casters, ensure brakes are engaged when stationary.
- Equipment does not fit: Verify that your equipment is 19-inch rack-mountable. Ensure you are using the correct mounting holes (square for IT, round for AV).
- PDU not working: Check the power connection to the PDU and ensure the surge protector switch is on. If issues persist, consult the PDU's specific manual or contact support.
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | OF5522S |
| Rack Units | 22U |
| Material | SPCC Cold-Rolled Carbon Steel |
| Color | Black (RAL9005 powder coat finish) |
| Product Dimensions (D x W x H) | 21.7" x 19.7" x 42.5" (550mm x 500mm x 1080mm) |
| Height with Casters | 45.5" (1155mm) |
| Item Weight | 35.8 pounds |
| Load Capacity (Leveling Feet) | Up to 600 lbs |
| Load Capacity (Casters) | Up to 500 lbs |
| Included Accessories | 2x Vented Rack Shelves, 1x 8-Outlet PDU with Surge Protector, Casters, Leveling Feet, Assembly Hardware |
9. Warranty and Support
RIVECO products are manufactured to high-quality standards. For warranty information, technical support, or any questions regarding your RIVECO 22U Open Frame Server Rack, please contact your retailer or visit the official RIVECO website. Please have your model number (OF5522S) and purchase date available when contacting support.