Robert Stevenson Lighting Addison Metal and Glass Outdoor Light Instruction Manual

1. Introduction

Thank you for choosing the Robert Stevenson Lighting Addison Metal and Glass Outdoor Light. This manual provides essential information for the safe installation, operation, and maintenance of your new outdoor lighting fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.

The Addison outdoor light features a modern architectural design with clear glass panels encased in a textured black metal frame. It is designed for outdoor use and is wet location rated, making it suitable for direct water exposure.

2. Safety Information

WARNING: RISK OF ELECTRIC SHOCK. Disconnect power at the circuit breaker or fuse box before installation or servicing.

• All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
• Ensure the fixture is properly grounded.
• Do not install this fixture with wet hands or while standing on a wet or damp surface.
• Use only bulbs of the specified type and wattage.
• Keep combustible materials away from the light fixture.

3. Package Contents

Verify that all components are present before installation:

• Addison Metal and Glass Outdoor Light Fixture
• Mounting Hardware (mounting bracket, screws, wire nuts, acorn nuts)
• Instruction Manual

Note: Bulb is not included.

4. Setup and Installation

This fixture requires hardwiring. Professional installation is recommended if you are not experienced with electrical wiring.

1. Prepare for Installation: Turn off power at the main circuit breaker or fuse box. Ensure the power is off before proceeding.
2. Mounting Bracket Installation: Attach the mounting bracket to the electrical junction box in the wall using the provided screws. Ensure the bracket is level.
3. Wiring Connections: Connect the fixture's wires to the house wiring using the provided wire nuts. Match the wires as follows:
   • Black (Live/Hot) to Black (Live/Hot)
   • White (Neutral) to White (Neutral)
   • Bare Copper or Green (Ground) to Bare Copper or Green (Ground)
   Carefully tuck all wires into the junction box.
4. Fixture Attachment: Align the fixture with the mounting bracket. Secure the fixture to the bracket using the two acorn nuts. Ensure the fixture is flush against the wall and securely fastened.
5. Bulb Installation: Refer to the 'Operating Instructions' section for bulb type and installation.
6. Restore Power: Once installation is complete and all connections are secure, restore power at the circuit breaker.

Image 1: Front view of the Addison Outdoor Light fixture. This image shows the overall design with the clear glass panels and textured black metal frame, ready for installation.

Image 2: Addison Outdoor Light with indicated dimensions of 9 inches (width) and 17 inches (height). This helps in planning the installation location.

Image 3: The Addison Outdoor Light installed on an exterior wall next to a door, demonstrating its appearance in a typical outdoor setting.

5. Operating Instructions

The Addison outdoor light is designed for simple operation once installed.

• Bulb Type: This fixture uses one E26 base incandescent bulb, maximum 100 watts. Edison-style bulbs are recommended for aesthetic purposes.
• Power On/Off: The light is controlled by an external wall switch (push button type) connected to its hardwired power source.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your outdoor light.

• Cleaning: To clean the fixture, ensure power is off. Wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents, as they may damage the finish or glass.
• Bulb Replacement: To replace the bulb, turn off power at the circuit breaker. The fixture's design requires access to the bulb by unscrewing the four screws located on the bottom cover (or top cover, depending on installation orientation). Carefully remove the cover, replace the E26 bulb (max 100W), then reattach the cover and secure the screws. Restore power.

Image 4: Close-up view of the top of the Addison Outdoor Light, showing the textured black finish. This area may need to be accessed for bulb replacement if the fixture is installed inverted.

7. Troubleshooting

If you encounter issues with your Addison outdoor light, refer to the following common problems and solutions:

• Light does not turn on:
  • Check the circuit breaker to ensure power is on.
  • Verify the bulb is securely screwed into the socket and is not burnt out.
  • Ensure all wiring connections are secure and correct.
• Light flickers:
  • Tighten the bulb in the socket.
  • Check for loose wiring connections.
  • Ensure the bulb wattage does not exceed the maximum rating.
• Difficulty replacing bulb:
  • Remember to turn off power before attempting bulb replacement.
  • The bulb is accessed by unscrewing the four screws on the bottom (or top) cover of the fixture.

8. Specifications

9. Warranty Information

This product is sold without an explicit manufacturer's warranty. Please refer to your retailer's return policy for any issues upon receipt.

10. Support

For further assistance or inquiries regarding your Robert Stevenson Lighting Addison Outdoor Light, please contact your point of purchase or refer to the retailer's customer service channels.