Instruction Manual

1. Product Overview

This manual provides essential information for the installation, maintenance, and troubleshooting of your AEagle Medium Lift Mower Blades. These blades are designed as replacement parts for various lawn mower models, primarily those with 46-inch decks. Proper installation and care will ensure optimal performance and longevity of the blades.

Image 1.1: Two AEagle Medium Lift Mower Blades, black in color, designed for efficient grass cutting.

2. Specifications

The AEagle Medium Lift Mower Blades are manufactured to specific dimensions and standards to ensure compatibility and performance.

• Material: Alloy Steel
• Color: Black
• Blade Type: Medium Lift Blade
• Center Hole: 5 Point Star
• Quantity: 2 Pack

Image 2.1: Detailed specifications of the mower blade, including length, width, thickness, and center hole type.

Dimensions:

Image 2.2: Close-up view of the 5-point star center hole, crucial for proper fit on compatible mower spindles.

Image 2.3: Visual representation of the blade's robust construction, highlighting thick side walls and quality bearings for increased longevity.

3. Installation Guide

Replacing mower blades requires caution. Always refer to your mower's specific owner's manual for detailed instructions and safety procedures.

Safety Precautions:

• Always disconnect the spark plug wire (for gas mowers) or remove the battery (for electric mowers) before working on the blades.
• Wear heavy-duty gloves to protect your hands from sharp edges.
• Ensure the mower is on a flat, stable surface and cannot roll or tip over.
• Use appropriate tools for loosening and tightening bolts.

Installation Steps (General):

1. Prepare the Mower: Disconnect power source. Tilt the mower onto its side with the carburetor/air filter facing up to prevent fuel/oil leaks.
2. Secure the Blade: Use a block of wood or a blade removal tool to prevent the blade from turning while you loosen the bolt.
3. Remove Old Blade: Loosen the blade bolt counter-clockwise with a wrench or socket. Remove the old blade and any washers or spacers, noting their order.
4. Clean Deck: Clean any accumulated grass clippings and debris from the underside of the mower deck.
5. Install New Blade: Position the new AEagle blade with the cutting edge facing the correct direction (usually indicated by an arrow or curve on the blade, or by matching the old blade's orientation). Ensure the 5-point star center hole aligns perfectly with the spindle.
6. Tighten Bolt: Reinstall any washers/spacers and the blade bolt. Tighten the bolt clockwise to the torque specification recommended in your mower's owner's manual. Ensure the blade is securely fastened and does not wobble.
7. Reconnect Power: Return the mower to its operating position and reconnect the spark plug wire or battery.

Image 3.1: An example of a mower blade being installed or cleaned on a mower deck, illustrating the area where the blades are attached.

4. Maintenance and Care

Regular maintenance of your mower blades is crucial for a clean cut and extended blade life.

• Cleaning: After each use, especially when mowing wet grass, clean the underside of the mower deck and the blades to prevent grass buildup. Grass buildup can unbalance the blades and reduce cutting efficiency.
• Inspection: Periodically inspect the blades for signs of wear, bending, or damage (e.g., nicks from hitting rocks). Damaged blades should be replaced immediately.
• Sharpening: While these are replacement blades, if you choose to sharpen them, ensure they are balanced after sharpening to prevent excessive vibration and damage to the mower. However, for optimal performance and safety, replacing worn blades is recommended.
• Storage: If storing the mower for an extended period, ensure blades are clean and dry to prevent rust.

5. Troubleshooting

If you experience issues after installing your new blades, consider the following common problems and solutions:

• Uneven Cut:
  • Cause: Blades installed incorrectly (upside down).
  • Solution: Recheck blade orientation. The cutting edge should be facing up towards the deck.
  • Cause: Blades are loose or unbalanced.
  • Solution: Ensure blade bolts are tightened to the manufacturer's specifications. Check for any debris stuck to the blades.
• Excessive Vibration:
  • Cause: Blades are unbalanced (e.g., due to uneven wear, damage, or improper sharpening).
  • Solution: Inspect blades for damage. If damaged, replace them. If recently sharpened, ensure they are properly balanced.
  • Cause: Blade bolt is loose.
  • Solution: Tighten the blade bolt securely.
• Poor Cutting Performance (Tearing Grass):
  • Cause: Blades are dull or damaged.
  • Solution: Replace the blades.
  • Cause: Grass is too wet or too tall.
  • Solution: Mow when grass is dry. Raise the cutting height for very tall grass and make multiple passes.

6. Compatibility

These AEagle Medium Lift Mower Blades are compatible with a range of models from various brands, primarily those with 46-inch decks. Always verify your mower's specific part number and deck size before purchase.

Replaces Part Numbers:

• Ariens: 21546611
• AYP: 403107, 405380, 40S380, 531309715, 532403107, 532405380, 917532403107, 917532405380, 917777405380, 594892801
• Craftsman: 33266, 403107
• Husqvarna: 403107, 503405380, 532403107, 532405380
• Poulan: 532405380, 575937901, 777405380, PP21011

Compatible with 46" Decks for Models such as:

• Poulan: PB185A46LT, PB18VA46, PB19546LT, PB20A46, PB20A46YT, PB20VA46, PB22H46YT, PP19H46, PP20VA46, PP22VH46
• Husqvarna: 2246LS, RZ 4619, RZ 4623, YTA 1946, YTA 22V46, YTH 18K46, YTH 20K46, YTH 2146, YTH 2146XP, YTH 21K46, YTH 2246TDR, YTH 22V46, YTH 22V46XLS, YTH 23K46, Z 246
• AYP: 2007 (requires 2 blades for 46" deck)

Image 6.1: Guidance on how to find the correct mower blade, emphasizing checking the owner's manual, manufacturer's website, and blade sizes.

7. Warranty and Support

AEagle Heavy Duty Lawn Mower Parts come with a One-Year Warranty.

For warranty claims, technical support, or further assistance, please contact the seller or AEagle customer service through the platform where the purchase was made. Ensure you have your purchase details and model number readily available.