Eurofase Yasmin 6 Light Large Outdoor Pendant Instruction Manual

1. Introduction

Thank you for purchasing the Eurofase Yasmin 6 Light Large Outdoor Pendant. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.

The Yasmin pendant features a vintage-inspired design with six lights, hand-blown glass shades, and an aged gold finish. It is designed for outdoor use and is wet-rated for durability in various weather conditions.

2. Safety Information

WARNING: Risk of electric shock. Disconnect power at the circuit breaker or fuse box before installation or servicing. Improper installation can result in electric shock or fire.

• All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Consult a qualified electrician if you are unfamiliar with proper electrical wiring installations.
• This fixture is intended for outdoor use and is wet-rated. Ensure all connections are properly sealed to prevent water intrusion.
• Do not install this fixture on a surface that is not structurally sound.
• Use only the specified bulb type and wattage. Refer to the "Specifications" section for details.
• Do not handle the fixture or attempt to replace bulbs while power is connected.
• Wear safety glasses and gloves during installation.

3. Package Contents

Carefully unpack your fixture and check that all parts are included. If any parts are missing or damaged, do not attempt to assemble or install the fixture. Contact customer support for assistance.

• Yasmin 6 Light Outdoor Pendant Fixture
• Instruction Manual
• Mounting Hardware (Canopy, Rods, Screws, Wire Nuts)
• Glass Shades

Note: Six (6) 60W incandescent bulbs (T10 base) are required but not included with this product.

4. Specifications

5. Setup and Installation

Important: Professional installation is recommended. Ensure power is disconnected at the circuit breaker before proceeding.

5.1. Preparation

1. Turn off the main power supply at the circuit breaker or fuse box.
2. Carefully remove the old fixture (if applicable).
3. Unpack the new fixture and lay out all components on a clean, flat surface. Refer to the "Package Contents" section to verify all parts are present.

5.2. Assembly

The fixture requires assembly. Follow the detailed instructions provided in the included assembly guide (if separate) or the general steps below:

1. Attach the desired length of extension rods to the fixture body and the canopy. The fixture includes rods of 3", 6", 12", and two 18" lengths, allowing for adjustable hanging height.
2. Thread the fixture wires through the rods and canopy.
3. Secure the glass shades onto the fixture arms. Ensure they are seated correctly and securely.
4. Install the recommended T10 base, 60W max incandescent bulbs (not included) into each socket.

5.3. Wiring and Mounting

1. Attach the mounting bracket (included in hardware) to the junction box in the ceiling using the provided screws.
2. Connect the electrical wires:
   • Connect the fixture's black wire to the house's black (hot) wire.
   • Connect the fixture's white wire to the house's white (neutral) wire.
   • Connect the fixture's ground wire to the house's ground wire (bare copper or green).
   Secure all connections with wire nuts and wrap with electrical tape for added safety.
3. Carefully tuck all wires into the junction box.
4. Mount the canopy to the mounting bracket, securing it with the decorative nuts or screws provided. Ensure the canopy is flush with the ceiling surface.

Image 1: Fully assembled Eurofase Yasmin 6 Light Outdoor Pendant with aged gold finish and clear glass shades.

Image 2: Detailed view of the pendant's aged gold frame and clear hand-blown glass shades, highlighting the vintage design elements.

6. Operating Instructions

Once the fixture is securely installed and wired, restore power at the circuit breaker.

• Turning On/Off: Operate the pendant using a standard wall switch connected to the fixture's circuit.
• Dimming: This fixture is dimmable. If connected to a compatible dimmer switch (sold separately), you can adjust the light intensity. Ensure you use dimmable incandescent bulbs for optimal performance.
• Bulb Replacement: To replace bulbs, first turn off power at the circuit breaker. Allow bulbs to cool completely. Carefully unscrew the old bulbs and screw in new T10 base, 60W max incandescent bulbs.

7. Maintenance

Regular maintenance will help preserve the appearance and functionality of your Eurofase Yasmin pendant.

• Cleaning: Turn off power and allow the fixture to cool. Wipe the metal parts with a soft, dry cloth. For glass shades, use a mild glass cleaner applied to a cloth, then wipe the shades. Avoid abrasive cleaners or solvents that could damage the finish or glass.
• Inspection: Periodically inspect the fixture for any signs of wear, loose connections, or damage, especially after severe weather. Ensure all screws and mounting hardware remain tight.
• Outdoor Environment: As an outdoor fixture, it is designed to withstand elements. However, regular cleaning can prevent buildup of dirt and debris, which can affect performance and appearance.

8. Troubleshooting

If you experience issues with your pendant, refer to the following troubleshooting guide:

If the problem persists after attempting these solutions, contact a qualified electrician or Eurofase customer support.

9. Warranty and Support

This Eurofase Yasmin pendant is backed by a 3-year extended warranty, which is a limited warranty covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical assistance, missing parts, or warranty inquiries, please contact Eurofase customer support. Refer to the official Eurofase website for current contact information.

Visit the Eurofase Store on Amazon for more information or to explore other products.