1. Product Overview
The LogiLink LPS402 Power Strip with Remote Control offers a convenient and energy-saving solution for managing your electronic devices. It features five protective contact sockets and integrated surge protection to safeguard your equipment. The included remote control allows you to switch devices on and off from a distance, and can even control a second compatible LogiLink power strip.
Image 1.1: The LogiLink LPS402 Power Strip, showing the five sockets, the main power plug, and the compact remote control.
Key Features:
- 5 Protective Contact Sockets: Provides ample connectivity for multiple devices.
- Remote Control Functionality: Control the power strip from up to 20 meters away.
- Multi-Strip Control: The remote can control up to two LogiLink power strips (second strip sold separately).
- Integrated Surge Protection: Protects connected devices from power surges, indicated by an LED light.
- Optimized Socket Layout: Sockets are angled at 45° for easier plug insertion.
- Increased Touch Protection: Sockets designed for enhanced safety.
- IP20 Rating: Protection against solid foreign objects greater than 12.5 mm and finger contact.
- Durable Cable: 1.5 m H05VV-F 3G 1.5 mm² cable for reliable power delivery.
2. Setup Instructions
2.1 Placement
Place the power strip on a flat, stable surface, away from direct sunlight, heat sources, and moisture. Ensure there is adequate ventilation around the unit. Avoid covering the power strip with carpets or other materials that could impede heat dissipation.
Image 2.1: The power strip discreetly placed on the floor, demonstrating a typical installation scenario.
2.2 Connecting the Power Strip
- Ensure the power strip's main switch (if present) is in the OFF position.
- Insert the power strip's plug firmly into a standard 230V / 16A wall outlet.
- Plug your devices into the five protective contact sockets on the power strip.
- If applicable, switch the main power strip switch to the ON position.
2.3 Remote Control Setup
The remote control is typically pre-paired with the power strip. If pairing is required or you wish to re-pair, follow these general steps:
- Ensure the power strip is plugged in and powered on.
- Locate the pairing button on the power strip (refer to the product diagram for exact location, usually a small button near the indicator lights).
- Press and hold the pairing button on the power strip for approximately 3-5 seconds until an indicator light (often green or blue) starts blinking.
- Within 10 seconds, press any ON button (e.g., ON-1) on the remote control.
- The indicator light on the power strip should stop blinking and remain solid, indicating successful pairing.
Image 2.2: A hand demonstrating the use of the remote control, highlighting its compact size and button layout.
3. Operating Instructions
3.1 Basic On/Off Control
Once the power strip is plugged in and devices are connected, use the remote control to manage power to the sockets.
- Press the ON-1 button on the remote to turn on all connected devices on the power strip.
- Press the OFF-1 button on the remote to turn off all connected devices on the power strip.
3.2 Controlling Multiple Power Strips
The remote control is designed to manage up to two LogiLink power strips. If you have a second compatible power strip (not included), you can pair it to the remote using the ON-2/OFF-2 buttons.
- To pair a second power strip, follow the pairing steps in Section 2.3, but press the ON-2 button on the remote during the pairing process.
- Once paired, use the ON-2 button to turn on the second power strip and OFF-2 to turn it off.
3.3 Surge Protection Indicator
The power strip features an LED indicator for surge protection. A green light typically indicates that the surge protection is active and functioning correctly. If this light is off or red, the surge protection may have been compromised by a significant power surge and the unit should be replaced.
4. Maintenance
4.1 Cleaning
- Always unplug the power strip from the wall outlet before cleaning.
- Use a soft, dry cloth to wipe down the exterior of the power strip and remote control.
- Do not use liquid cleaners, aerosols, or solvents, as these can damage the unit or pose an electrical hazard.
- Ensure no moisture enters the sockets or internal components.
4.2 Safety Precautions
- Do not overload the power strip beyond its maximum rated power (3680 W).
- Do not connect multiple power strips in series (daisy-chaining).
- Do not use the power strip in wet or damp environments.
- Keep out of reach of children and pets.
- Do not disassemble or attempt to repair the power strip or remote control. Refer to qualified personnel for service.
- Regularly inspect the power cord and plug for any signs of damage. If damaged, discontinue use immediately.
5. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Power strip does not turn on. | Not plugged in correctly; Wall outlet has no power; Main switch is OFF. | Ensure plug is fully inserted. Check wall outlet with another device. Turn main switch ON. |
| Remote control does not work. | Remote battery is low or dead; Remote is out of range; Remote is not paired. | Replace remote battery. Move closer to the power strip (within 20m). Re-pair the remote control (see Section 2.3). |
| Devices connected to the power strip do not turn on/off. | Power strip is overloaded; Device itself is off or faulty. | Reduce the total wattage of connected devices. Check if the individual device is powered on and functioning correctly. |
| Surge protection LED is off or red. | Surge protection has been activated/compromised. | The power strip may no longer provide surge protection. It is recommended to replace the unit. |
6. Technical Specifications
| Feature | Specification |
|---|---|
| Model Number | LPS402 |
| Total Power Outlets | 5 x CEE 7/3 (Protection Contact) |
| Voltage | 230 V |
| Current | 16 A |
| Frequency | 50 Hz |
| Maximum Power | 3680 W |
| Cable Specifications | H05VV-F 3G 1.5 mm² |
| Cable Length | 1.5 m |
| Remote Control Range | Up to 20 m (open field) |
| Protection Rating | IP20 |
| Color | White |
| Product Dimensions | 16.42 x 2.2 x 1.65 inches |
| Item Weight | 1.49 pounds |
7. Warranty Information
LogiLink products are manufactured with high-quality materials and undergo strict quality control. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official LogiLink website. Keep your purchase receipt as proof of purchase for any warranty claims.
8. Support
For further assistance, technical support, or inquiries regarding your LogiLink LPS402 Power Strip, please contact LogiLink customer service. Contact information can typically be found on the product packaging, the official LogiLink website, or through your retailer.
Manufacturer: 2direct GmbH
Website: Please refer to the official LogiLink website for up-to-date support information.
