Product Overview
This document provides essential information for the safe and effective use of the saschedross USB Type C Charging Cable. This cable is designed to provide 5V DC power supply for various Tribit Bluetooth Wireless Speakers.
Compatible Models:
- Tribit StormBox Pro Model BTS31
- Tribit XSound Surf BTS21
- Tribit StormBox Micro BTS10
- Tribit XSound Go TS-BTS20
Figure 1: Front view of the USB Type C Charging Cable, showing both the USB-A and USB-C connectors.
Figure 2: The USB Type C Charging Cable coiled, highlighting its flexibility and compact storage.
Safety Information
- Do not expose the cable to extreme temperatures or direct sunlight.
- Avoid bending or twisting the cable excessively, as this may damage internal wires.
- Keep out of reach of children and pets.
- Use only with compatible devices as specified in this manual.
- Disconnect the cable from the power source when not in use.
Setup
Setting up the USB Type C Charging Cable is straightforward. Follow these steps to ensure proper connection and charging.
- Identify Ports: Locate the USB-A port on your power adapter (e.g., wall charger, computer USB port) and the USB-C charging port on your compatible Tribit speaker.
- Connect USB-A: Insert the standard USB-A end of the charging cable into a compatible USB-A power source. Ensure it is fully inserted.
- Connect USB-C: Insert the USB-C end of the charging cable into the USB-C charging port on your Tribit speaker. Ensure it is fully inserted and clicks into place.
- Verify Connection: Once connected, your speaker should indicate that it is charging, typically via an LED indicator light.
Operating Instructions
This cable is designed for charging compatible devices. It does not transmit data.
- Charging: Connect the cable as described in the "Setup" section. The cable will facilitate the transfer of 5V DC power from the source to your speaker.
- Charging Time: Charging time will vary depending on the power output of your adapter and the battery capacity of your speaker. Refer to your speaker's manual for specific charging times.
- Disconnection: To disconnect, gently pull the connectors straight out from the ports. Avoid pulling the cable by the cord itself.
Maintenance
Proper maintenance will extend the lifespan of your charging cable.
- Cleaning: Use a soft, dry cloth to wipe the cable and connectors. Do not use liquid cleaners or abrasive materials.
- Storage: When not in use, coil the cable loosely and store it in a cool, dry place away from direct sunlight and extreme temperatures. Avoid tight coiling or kinking.
- Inspection: Periodically inspect the cable for any signs of damage, such as frayed wires, bent connectors, or cracked insulation. If damage is found, discontinue use immediately.
Troubleshooting
If you encounter issues with your charging cable, try the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Device not charging. | Cable not fully inserted. Faulty power adapter. Incompatible device. Damaged cable. | Ensure both ends of the cable are securely connected. Try a different power adapter. Verify your device is listed as compatible. Inspect the cable for damage; replace if necessary. |
| Slow charging. | Low power output from adapter. Using a non-optimal USB port (e.g., low-power computer port). | Use a higher wattage power adapter (e.g., 5V/2A). Connect to a dedicated wall charger or a high-power USB port. |
| Cable feels hot during charging. | Normal operation (slight warmth). Overload or short circuit. | Slight warmth is normal. If it's excessively hot, disconnect immediately and check for damage or incompatible devices. |
Specifications
| Feature | Detail |
|---|---|
| Brand | saschedross |
| Connector Type | USB Type C (Male) to USB Type A (Male) |
| Cable Type | USB |
| Compatible Devices | Tribit StormBox Pro Model BTS31, Tribit XSound Surf BTS21, Tribit StormBox Micro BTS10, Tribit XSound Go TS-BTS20 Bluetooth Wireless Speakers |
| Recommended Use | Charging, Connecting to portable speakers |
| Color | Black |
| Power Output | 5V DC (Input from power source) |
| Manufacturer | Shenzhen Waweis Technology Co., Ltd |
| FCC Compliance | Yes |
Warranty and Support
This product is manufactured by Shenzhen Waweis Technology Co., Ltd under the saschedross brand.
For specific warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. Typically, charging cables come with a limited warranty against manufacturing defects.
For technical support or inquiries, please contact the seller or manufacturer directly. Information may be available on the product packaging or the seller's online storefront.
Seller: TATMALL
Manufacturer: Shenzhen Waweis Technology Co., Ltd