Introduction
The TORC T9 Full Face Retro Motorcycle Helmet is engineered to provide superior protection and comfort for motorcycle riders. This manual provides essential information regarding the helmet's features, proper usage, maintenance, and safety guidelines to ensure optimal performance and longevity.
Figure 1: Front-side view of the TORC T9 Full Face Retro Motorcycle Helmet in Gloss White.
Safety Information
Your safety is paramount. This helmet meets and exceeds the safety standards required for motorcycle helmets. Always ensure proper fit and secure fastening before riding.
- DOT & ECE Approved: This helmet complies with US Federal Motor Vehicle Safety Standard 218 (FMVSS 218) and ECE homologation standards, ensuring a high level of protection.
- Proper Fit: A helmet must fit snugly to provide effective protection. Refer to the "Setup and Fitting" section for detailed instructions on how to achieve a proper fit.
- Chin Strap: Always secure the padded chin strap using the D-ring closure system. The strap should be tight enough so that the helmet cannot be easily removed or shifted.
- Impact Protection: The multi-density EPS (Expanded Polystyrene) liner is designed to absorb impact energy. Any helmet that has sustained an impact should be replaced immediately, even if visible damage is not apparent.
Figure 2: The TORC T9 helmet is certified to both DOT FMVSS No. 218 and ECE22.05 safety standards.
Setup and Fitting
Achieving the correct helmet fit is crucial for safety and comfort. Follow these steps to ensure your TORC T9 helmet fits properly:
- Measure Your Head: Use a flexible measuring tape to measure the circumference of your head. Wrap the tape around the fullest part of your head, approximately half an inch above your eyebrows and ears. This measurement will help you select the correct shell size.
- Consult the Size Chart: Refer to the size chart below to find the recommended helmet size based on your head measurement.
- Try On the Helmet:
- The helmet should feel snug all around your head, with no pressure points.
- The cheek pads should press firmly against your cheeks.
- The helmet should not move freely when you shake your head from side to side or up and down.
- The top of the eye port should be just above your eyebrows, allowing for clear vision.
- Secure the Chin Strap: Fasten the D-ring chin strap securely. It should be tight enough that you cannot pull the helmet off your head when pulling upwards from the rear.
Figure 3: Detailed helmet size chart and head measurement instructions for accurate fitting.
Operating and Features
The TORC T9 helmet incorporates several features designed for rider comfort and performance:
- Ventilation System: The helmet features an advanced airflow system with adjustable crown intake ports and chin vents with metal mesh intake. Air is channeled through the multi-density EPS to exhaust ports, helping to regulate temperature and reduce fogging.
Figure 4: Illustration of the helmet's 6 intake vents (2 forehead, 4 chin-bar) and 4 exhaust vents (2 top-rear, 2 bottom-rear) for optimal airflow.
- Face Shield: The helmet comes with a removable anti-scratch and anti-fog resistant shield. Optional colored shields are available for purchase. The shield features a secure locking system and a quick-change coin-operated pivot kit for easy removal and installation.
Figure 5: Close-up view of the quick-change coin-operated pivot kit and shield secure locking system.
- Liner: The interior features a sweat-wicking faux suede liner, designed for comfort and moisture management. The liner is removable and washable for hygiene.
Figure 6: The helmet's interior showing the comfortable, sweat-wicking faux suede liner.
Maintenance
Proper maintenance will extend the life of your helmet and ensure its protective capabilities.
- Cleaning the Shell: Use a soft cloth and mild soap with water to clean the exterior shell. Avoid abrasive cleaners or solvents, as they can damage the finish and protective coatings.
- Cleaning the Liner: The removable liner can be hand-washed with mild soap and water. Allow it to air dry completely before reinserting into the helmet. Do not machine wash or tumble dry.
- Cleaning the Face Shield: Clean the face shield with a soft, damp cloth and mild soap. Rinse thoroughly with clean water and allow to air dry. Do not use abrasive materials or chemical cleaners that could scratch or damage the anti-fog/anti-scratch coatings.
- Storage: Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Use a helmet bag to protect it from dust and scratches.
Troubleshooting
If you encounter issues with your helmet, consider the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Face shield becomes loose or detaches during use. | Pivot kit screws or retaining washers are loose or missing. | Ensure the quick-change coin-operated pivot kit screws and retaining washers are securely tightened. Regularly check these components for tightness before each ride. If parts are missing, contact customer support for replacements. |
| Helmet feels too loose or shifts while riding. | Incorrect size or chin strap not properly secured. | Re-evaluate your helmet size using the size chart and fitting instructions. Ensure the D-ring chin strap is pulled tight and properly fastened. |
| Excessive fogging of the face shield. | Insufficient airflow or extreme temperature/humidity. | Ensure all intake and exhaust vents are open. The shield has anti-fog properties, but in extreme conditions, opening the shield slightly or using additional anti-fog treatments may be necessary. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | T902:25 |
| Shell Type | Composite Fiberglass |
| Liner Material | Multi-density EPS, Sweat-wicking faux suede |
| Ventilation | Adjustable crown intake ports, Chin vents with metal mesh, 4 barrel metal mesh exhaust ports |
| Face Shield | Removable anti-scratch & anti-fog resistant, Quick-change coin-operated pivot kit |
| Closure Type | Padded chin strap with D-ring closure |
| Safety Standards | Meets DOT FMVSS No. 218 & ECE homologation standards |
| Weight (XS-M) | 1450 +/- 50g |
| Weight (L-XXL) | 1550 +/- 50g |
| Fit Type | Medium Oval |
| Product Dimensions | Approximately 16 x 12 x 12 inches (varies by size) |
| Item Weight | Approximately 3 pounds (varies by size) |
Warranty and Support
This TORC T9 Full Face Retro Motorcycle Helmet comes with a 1-year manufacturer warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.
For warranty claims, technical support, or replacement parts, please contact TORC customer service through their official website or the retailer where the helmet was purchased. Please have your proof of purchase and helmet model number (T902:25) ready when contacting support.
For more information, visit the official TORC Store on Amazon.