VLAND Headlights Assembly for 2019-2024 Dodge Ram 1500 (Model tcc-6001)

1. Important Safety Information

• Professional installation is recommended for optimal functionality and safety.
• Always wear appropriate personal protective equipment (PPE) when working on any vehicle.
• Exercise caution when handling vehicle body parts, such as the bumper, to prevent scratching or damage.
• Avoid direct contact with halogen bulbs or wire assemblies until the unit has cooled down after use.
• If you encounter any difficulties not covered in this manual, seek assistance from a qualified automotive technician.

2. Package Contents

Verify that all items are present in your package:

• One (1) set of left and right headlights
• One (1) instruction manual
• One (1) ACC harness
• Two (2) adapter harnesses (for factory reflector version)

Image: A pair of VLAND Headlight Assemblies, showing both the driver and passenger side units.

3. Compatibility

This VLAND Headlights Assembly is designed for the following vehicles:

• 2019-2024 Dodge Ram 1500 5th Gen (DT) new body headlight models:
  • Tradesman (factory halogen)
  • Tradesman HFE Bighorn
  • Laramie (factory reflector)
  • Rebel
  • Lone Star

Note: This product is not compatible with old body models, Ram 2500/3500, Classic/TRX/Limited/Longhorn models.

Image: A white Dodge Ram 1500 truck, illustrating the compatible vehicle type for the headlight assembly.

4. Tools Required

The following tools are recommended for installation:

• Trim Pad Remover
• 10mm Wrench
• Ratchet
• 6" long Socket Extension
• 10mm Socket
• 8mm Socket
• Needle Nose Pliers
• Pick Tool
• T25 Torx Bit

5. Installation Instructions

Follow these steps carefully to install your new VLAND Headlights Assembly. Professional installation is recommended.

Step 1: Prepare Vehicle

1. Raise the hood of your vehicle.
2. Remove the twelve plastic fasteners on the radiator upper support cover using a trim pad remover. Then, remove the radiator upper support cover.

Step 2: Remove Grille Trim

3. Remove the eight 10mm bolts at the top of the upper grille trim. Then, remove the upper grille trim.

Step 3: Access Headlight Bolts

4. Remove the four 8mm bolts on the fender liner.
5. Pull away the fender liner and remove the 10mm bolt.
6. Grab the edge of the filler panel and pull forward to unseat it. Repeat for the other end and the opposite side of the vehicle.
7. Remove the three 10mm bolts at the bottom of the front grille for both sides.

Step 4: Remove Headlight Assembly

8. Remove the 10mm bolt at the bottom of the headlight.
9. Remove the 10mm bolt at the top of the headlight.
10. Disconnect the headlight harness and remove the factory headlight housing.

Step 5: Transfer Components

11. Remove the signal light socket, parking light socket, and high and low beam light bulbs from the factory headlight housing.
12. Remove the signal light bulb from the signal light socket.
13. Reinstall the signal light bulb, parking light socket, and high and low beam light bulbs into the new headlight housing.

Image: Rear view of the headlight assembly, highlighting the harness assembly, signal cable plug, ACC plug, and adjustment screws for low/high beam horizontal and vertical alignment.

Step 6: Install New Headlights

14. Connect the headlight harness and seat the new headlight assembly in place.
15. Reinstall the 10mm headlight bolt at the top of the headlight.
16. Reinstall the 10mm headlight bolt at the bottom of the headlight, and repeat the steps for the opposite side.

Step 7: DRL Wiring (for Halogen Equipped Vehicles)

If your vehicle was originally equipped with halogen headlights, follow these steps for the Daytime Running Light (DRL) wiring:

17. Remove the fuse box cover.
18. Remove the #35 fuse using needle nose pliers.
19. Install the ACC wire fuse into the #35 fuse spot.
20. Reinstall the fuse box cover.
21. Connect the ACC wire to the LH headlights connector.
22. Connect the ACC wire to the RH headlights connector.
23. Cable tie any loose wires to secure them.

Step 8: Reassembly

24. Reinstall the front grille.
25. Reinstall the four 10mm bolts at the top of the front grille.
26. Reinstall the three 10mm bolts at the bottom of the front grille for both sides.
27. Reinstall the filler panel.
28. Pull away the fender liner and reinstall the 10mm bolt.
29. Reinstall the fender liner and the four 8mm bolts.
30. Reinstall the upper grille trim and the eight 10mm bolts.
31. Reinstall the radiator upper support cover and the twelve plastic fasteners.
32. Close the hood to complete the installation.

6. Functionality Check

After installation, perform the following checks to ensure proper operation:

• Start the car and verify that the LED light bar (DRL) is working correctly.
• Test the low beam lights.
• Test the high beam lights.
• Test the dynamic turn signal indicators.

Image: Close-up of the VLAND Headlight showing the sequential turn indicator in action.

Image: Diagram illustrating the various lighting functions of the VLAND Headlight: LED Dipped Beam Light, Daytime Running Light, LED Main Beam Light, and Turn Signal.

7. Specifications

Image: Features of the VLAND Headlight, including Premium LED Technology, Easy Installation, and compliance with DOT/SAE Standards.

Image: Details on DOT/SAE Certification, highlighting compliance with standards, photometric consideration, safety compliance, and testing in simulated rain/humidity/shock conditions.

8. Warranty & Support

This VLAND Headlights Assembly comes with a 1-year warranty.

The product is DOT or SAE certified, with PC, ABS, PMMA, and GLASS materials proven to be fully sealed, waterproof, dust, and corrosion resistant, ensuring perfect functionality even in harsh weather conditions.

For further assistance with fitment or any other inquiries, please contact VLAND customer support.