COOLFOX Electric Automatic Foam Blaster QHX-551A-2 User Manual

Introduction

Thank you for choosing the COOLFOX Electric Automatic Foam Blaster. This manual provides essential information for the safe assembly, operation, and maintenance of your new foam blaster. Please read all instructions carefully before use to ensure proper function and safety.

Safety Information

WARNING: Not suitable for children under 6 years. Adult supervision is recommended.

• Always wear eye protection when operating the foam blaster.
• Do not aim at eyes or face.
• Use only the soft foam darts provided or compatible darts designed for this product.
• Do not modify the foam blaster or darts.
• Keep fingers and loose clothing away from moving parts.
• Ensure the play area is clear of obstacles and other people before firing.

Package Contents

Verify that all items listed below are included in your package:

• COOLFOX Electric Automatic Foam Blaster (Main Body)
• Gun Barrel and Barrel Extension
• Front Sight and Sight (Scope)
• Tactical Grip
• Magazine(s)
• 100 Soft Foam Darts (two shapes: suction plate and ordinary)
• Gunstock
• Rechargeable Lithium Ion Battery
• USB Charging Cable

Image: The COOLFOX Electric Automatic Foam Blaster with all its components and 100 soft foam darts.

Setup and Assembly

1. Component Identification

Image: Labeled diagram of the foam blaster's main components.

2. Assembly Steps

Follow these steps to assemble your foam blaster:

1. Install the Barrel & Gun Appendage: Attach the gun barrel to the main body.
2. Install the Barrel Grip & Front Sight: Secure the barrel grip and front sight onto the barrel.
3. Install the Silencer (if applicable): Attach the silencer to the end of the barrel.
4. Install the Gunstock: Slide the gunstock onto the rear of the main body until it clicks into place.
5. Install the Scope & Tactical Grip: Attach the scope and tactical grip to their respective rails on the blaster.
6. Insert the Magazine: Press the clip button and insert the loaded magazine into the blaster.

Image: Visual guide for assembling the foam blaster.

3. Battery Installation and Charging

The foam blaster uses a rechargeable Lithium Ion battery. Ensure the battery is fully charged before first use.

• Locate the battery compartment, typically on the side or rear of the blaster.
• Connect the battery to the blaster's internal connector.
• Close the battery compartment securely.
• To charge, connect the battery to the provided USB charging cable and plug it into a compatible USB power source.
• A full charge typically provides 3-6 hours of play.

4. Loading Darts

Proper dart loading prevents jams and ensures optimal performance.

• Insert soft foam darts into the magazine.
• Important: Do not fill the magazine completely. Leave room for one or two darts at the top to prevent blockages and ensure smooth feeding.

Images: Loading darts into the magazine and a view of the magazine with darts.

Operation

1. Power On/Off

Locate the power switch on the blaster. Slide it to the 'ON' position to activate the blaster. Slide to 'OFF' when not in use to conserve battery.

2. Firing Modes

The COOLFOX Electric Automatic Foam Blaster offers three distinct firing modes:

• Single Shot: Fires one dart per trigger pull.
• 3-Burst: Fires three darts with a single trigger pull.
• Continuous Burst: Fires darts continuously as long as the trigger is held down.

Use the mode selector switch, typically located near the trigger, to cycle between these modes.

Image: Visual representation of the three launch modes.

3. Firing Instructions

1. Ensure the battery is charged and installed, and the magazine is loaded with darts.
2. Turn the power switch to 'ON'.
3. Select your desired firing mode.
4. Aim at your target, ensuring no people or animals are in the line of fire.
5. Pull the trigger to fire. The blaster will emit realistic shooting sounds.

Image: Foam darts with suction cups can adhere to smooth surfaces like glass.

Maintenance

• Cleaning: Wipe the blaster with a dry, soft cloth. Do not use water or harsh chemicals.
• Storage: Store the blaster and darts in a cool, dry place away from direct sunlight. Remove the battery if storing for extended periods.
• Battery Care: Recharge the battery regularly, even if not in use, to maintain its lifespan.

Troubleshooting

Specifications

Warranty and Support

For warranty information, technical support, or any questions regarding your COOLFOX Electric Automatic Foam Blaster, please contact the manufacturer directly through their official website or the retailer where the product was purchased. Keep your purchase receipt as proof of purchase.