1. Safety Information
- Read all instructions carefully before installation. Incorrect assembly may result in damage or injury.
- Ensure your monitor's weight and size are within the specified limits for this adapter.
- Do not overtighten screws, as this may strip threads or damage components.
- Verify that power and video ports on your monitor are not blocked by the bracket after installation.
- This adapter is not suitable for curved monitors.
2. Compatibility
This VESA mount adapter is designed for:
- Monitors ranging from 17 to 27 inches.
- Monitors weighing 8kg (17.6 lbs) or less.
- Monitors with a screen thickness between 1 inch (25.4mm) to 2.75 inches (69.85mm).
- Monitors with a bezel height from 266mm to 412mm.
- Converts non-VESA compatible monitors to 75mm x 75mm or 100mm x 100mm VESA patterns.
Please verify your monitor's specifications before proceeding with installation.
Image: Diagram illustrating compatible monitor sizes (17", 21", 27") and maximum weight capacity (up to 8kg/17.6lbs), along with thickness and bezel height measurements.
3. Package Contents
Please ensure all components are present before beginning installation:
- 1 x VESA Mount Adapter Bracket Set (4 arms)
- 1 x Mounting Hardware Kit (various screws, nuts, washers, wrench)
- 1 x User Manual (this document)
Note: A VESA mount arm or pole is not included with this adapter kit.
Image: A flat lay of all included parts: four adapter arms, various screws, nuts, washers, and a small wrench.
4. Setup and Installation
4.1. Assembling the Adapter Arms
Follow these steps to assemble the adapter arms to the VESA plate (not included):
- Attach the four adapter arms to the central VESA plate using the provided screws and nuts. Ensure the arms are oriented correctly to form an 'X' shape.
- Use the small wrench to tighten the nuts securely.
Image: An illustration of the VESA mount adapter arms assembled and attached to a monitor arm (monitor arm not included).
Image: Rear view of a monitor with the VESA adapter installed, highlighting the 75x75mm and 100x100mm VESA patterns it creates.
4.2. Attaching the Adapter to Your Monitor
This adapter is designed for monitors without VESA mounting holes. The arms clamp onto the monitor's edges.
- Place your monitor face down on a soft, clean surface to prevent scratches.
- Position the assembled VESA adapter over the back of your monitor.
- Carefully slide the top two arms over the top edge of your monitor. Ensure the soft padding on the arms protects the monitor's bezel.
- Adjust the arms so they securely grip the top and bottom edges of the monitor. The bottom arms have adjustable screws to tighten the grip.
- Tighten the screws on the bottom arms until the monitor is held firmly in place. Do not overtighten.
Image: A monitor with the non-VESA adapter installed, showing how the arms clamp onto the monitor's edges.
Image: Installation guidance for small screens, illustrating how the bracket can be adjusted to fit various monitor sizes.
4.3. Video Installation Guides
For a visual guide, please refer to the following installation videos:
Video: A detailed step-by-step guide on how to install the suptek Universal VESA Mount Bracket Adapter.
Video: Another comprehensive installation video for the suptek Universal VESA Mount Bracket Adapter.
Video: A general overview of the Universal VESA Mount Bracket and its installation process.
5. Operating Instructions
Once the adapter and monitor are securely attached to a VESA-compatible monitor arm (not included), you can adjust your monitor's position as allowed by your specific monitor arm.
- Adjusting Monitor Angle: Use the adjustment mechanisms on your monitor arm to tilt, swivel, or rotate the monitor to your desired viewing angle.
- Height Adjustment: If your monitor arm supports height adjustment, use its controls to set the monitor to an ergonomic height.
- Cable Management: Route monitor cables through any integrated cable management features on your monitor arm to maintain a tidy workspace.
6. Maintenance
- Periodically check all screws and connections to ensure they remain tight. Retighten if necessary.
- Clean the adapter and monitor arms with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Inspect the soft padding on the adapter arms for wear and tear. Replace if damaged to prevent monitor scratches.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Monitor feels loose or unstable. | Screws on adapter arms are not tight enough. | Ensure all screws on the adapter arms are securely tightened. Do not overtighten. |
| Bottom hooks do not reach or secure the monitor. | Monitor thickness or bezel height exceeds compatibility. | Verify your monitor's dimensions against the compatibility specifications (1" to 2.75" thickness, 266-412mm bezel height). This adapter may not be suitable for your monitor. |
| Power/video ports are blocked. | Adapter arms are positioned incorrectly. | Adjust the position of the adapter arms to ensure all ports are accessible. The arms can be slightly repositioned along the VESA plate. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | suptek |
| Model Number | Vesa Mount Adapter Bracket Set |
| Compatible Monitor Size | 17" to 27" |
| Weight Capacity | Up to 8 kg (17.6 lbs) |
| Screen Thickness Compatibility | 1" to 2.75" (25.4mm to 69.85mm) |
| Bezel Height Compatibility | 266mm to 412mm |
| VESA Compatibility | 75mm x 75mm, 100mm x 100mm |
| Material | High-quality steel with durable plastic grips |
| Color | Black |
| Item Weight | 1.29 pounds |
Image: Visual representation of product dimensions, weight capacity, and VESA pattern compatibility.
9. Warranty and Support
For warranty information or technical support, please contact suptek customer service through the retailer where the product was purchased or visit the official suptek website.
Keep your purchase receipt as proof of purchase for any warranty claims.
