Intellitronix LED Digital Gauge Panel Instruction Manual

Product Overview

The Intellitronix LED Digital Gauge Panel DP1805B is a modern replacement for the original instrument cluster in 1970-1976 Dodge Duster and Dart vehicles. This panel provides clear, digital readouts for various vehicle parameters, enhancing visibility and accuracy. It includes a speedometer, tachometer, water temperature gauge, oil pressure gauge, voltmeter, and fuel level gauge, along with integrated turn signal and high beam indicators.

Figure 1: Intellitronix LED Digital Gauge Panel (Blue) installed in a dashboard.

The system comes complete with direct-fit printed circuit boards, a custom-fit "smoked" plexiglass faceplate, and necessary sending units for temperature, oil pressure, and speedometer. It is designed for vehicles without electronic transmission or cruise control, with provisions for electronic cruise control senders.

Package Contents

Verify that all components are present before beginning installation:

• LED Digital Gauge Panel (Printed Circuit Board with integrated displays)
• "Smoked" Plexiglass Faceplate
• Universal Temperature Sending Unit (S8023)
• Oil Pressure Sending Unit
• Universal Speedometer Sending Unit (S9013)
• Installation Instructions
• Necessary wiring harnesses and connectors

Figure 2: Included components of the Intellitronix Digital Gauge Panel kit.

Note: The original vehicle bezel is NOT included and is required for installation.

Setup and Installation

Installation of the Intellitronix LED Digital Gauge Panel requires basic automotive electrical and mechanical knowledge. Professional installation is recommended if you are not familiar with these procedures.

Pre-Installation Steps:

1. Disconnect the vehicle's battery to prevent electrical shorts.
2. Carefully remove the existing instrument cluster from the dashboard. Refer to your vehicle's service manual for specific removal procedures.
3. Remove the original gauges and wiring from the existing bezel.

Panel Installation:

1. Mount the Intellitronix LED Digital Gauge Panel circuit board into your original vehicle bezel. Ensure a secure fit.
2. Attach the "smoked" plexiglass faceplate over the digital displays.
3. Connect the provided wiring harness to the appropriate connections on the circuit board.

Sending Unit Installation:

• Speedometer: If your vehicle is not equipped with a functional electronic cruise control sender, install the Intellitronix S9013 universal speedometer sending unit. Connect it to the vehicle's transmission output or drive shaft as per the unit's instructions.
• Water Temperature: Replace the existing temperature sending unit with the provided S8023 unit. Ensure the correct bushing size (1/2 inch is standard, 3/8 inch available upon request) is used for a proper fit.
• Oil Pressure: Install the provided oil pressure sending unit in place of the original unit.
• Fuel Level: The panel is designed to work with the existing Chrysler 73-10 ohms fuel level sending unit. No replacement is typically needed for this component.
• Voltmeter: No separate sending unit is required for the voltmeter as it reads directly from the vehicle's electrical system.

Wiring Connections:

Carefully connect the wiring harness from the gauge panel to the vehicle's electrical system. Ensure all connections are secure and properly insulated. Refer to the detailed wiring diagram included with your product for specific connections, including power, ground, illumination, turn signals, and high beam indicators.

1. Connect the main power wire to a switched 12V source.
2. Connect the ground wire to a reliable chassis ground point.
3. Connect the illumination wire to the vehicle's dash light circuit for dimming functionality.
4. Connect the turn signal and high beam indicator wires to their respective vehicle circuits.

Post-Installation:

1. Once all connections are made, carefully re-install the assembled gauge panel into the dashboard opening.
2. Reconnect the vehicle's battery.
3. Test all functions of the gauge panel before fully securing the dashboard trim.

Operating Instructions

General Operation:

Upon vehicle ignition, the digital displays will illuminate, showing real-time data for each parameter. The brightness of the display can typically be adjusted via the vehicle's dimmer switch, if connected to the illumination circuit.

Speedometer Functions:

• Reads up to 255 MPH.
• Displays odometer and trip meter.
• One-button calibration: Allows for calibration regardless of tire size, gear ratio, or transmission.
• Performance metrics: Includes 0-60 time, 1/4 mile elapsed time, and high-speed recall, accessible with a push of a button.

Tachometer Functions:

• Displays 0-9999 RPM.
• Adjustable for 1, 2, 4, 6, 8, 10, or 12 cylinder engines.
• High RPM recall function.

Other Gauge Functions:

• Water Temperature: Displays 18-275°F range.
• Oil Pressure: Reads 0-100 PSI range.
• Voltmeter: Displays 7.0 to 18.0 volt range.
• Fuel Level: Reads 0-99% range in 1% increments.

Maintenance

The Intellitronix LED Digital Gauge Panel is designed for long-term reliability with minimal maintenance. The primary maintenance involves keeping the plexiglass faceplate clean and ensuring all electrical connections remain secure.

• Cleaning: Use a soft, lint-free cloth and a mild, non-abrasive cleaner specifically designed for plastics or automotive interiors to clean the plexiglass faceplate. Avoid harsh chemicals or abrasive materials that could scratch the surface.
• Electrical Connections: Periodically check all wiring connections to the gauge panel and sending units to ensure they are tight and free from corrosion. Loose connections can lead to inaccurate readings or intermittent operation.
• Sensor Integrity: While designed for durability, ensure that the temperature, oil pressure, and speedometer sending units are not physically damaged and their wiring is intact.

Troubleshooting

If you experience issues with your Intellitronix LED Digital Gauge Panel, refer to the following common troubleshooting steps:

If these steps do not resolve the issue, contact Intellitronix customer support for further assistance.

Specifications

• Model: DP1805B
• Compatibility: 1970-1976 Dodge Duster/Dart (also fits 1968-1977 Scamp, 1968-1977 Valiant, 1969-1976 Dart, 1973-1976 Dart Sport, 1972 Demon)
• Speedometer: 0-255 MPH, Odometer, Trip Meter, 0-60 time, 1/4 mile ET, High Speed Recall, One-button calibration.
• Tachometer: 0-9999 RPM, 1-2-4-6-8-10-12 Cylinder selectable, High RPM Recall.
• Water Temperature: 18-275°F range (with S8023 sending unit).
• Oil Pressure: 0-100 PSI range (with included sending unit).
• Voltmeter: 7.0-18.0 Volts range.
• Fuel Level: 0-99% range (compatible with Chrysler 73-10 ohms sender).
• Indicators: Turn Signals, High Beam.
• Materials: Copper, Fiberglass, Acrylic.
• Dimensions (Product): Approximately 8 x 16 x 4 inches (L x W x H).
• Weight: Approximately 3 Pounds.

Warranty Information

Intellitronix products are typically backed by a limited warranty covering defects in materials and workmanship. For specific warranty terms, duration, and claim procedures, please refer to the warranty card included with your product or visit the official Intellitronix website. Keep your proof of purchase for warranty claims.

Customer Support

For technical assistance, installation questions, or warranty inquiries, please contact Intellitronix customer support:

• Website: www.intellitronix.com (Check for updated contact information or FAQs)
• Phone: Refer to the Intellitronix website or product packaging for current phone numbers.
• Email: Refer to the Intellitronix website for current email contact.

When contacting support, please have your product model number (DP1805B) and purchase information readily available.