1. Introduction
Thank you for choosing the EraClean Ultrasonic Contact Lens Cleaner. This device is designed to provide deep and efficient cleaning for various types of contact lenses, including soft, rigid, and colored lenses, using 56KHz ultrasonic wave technology. Regular cleaning helps remove dust, tear proteins, and other impurities, contributing to better eye hygiene and comfort. Please read this manual thoroughly before use to ensure proper operation and maintenance.
2. Product Overview and Components
The EraClean GM02 is a compact and portable 3-in-1 contact lens cleaner. It integrates essential accessories for convenience.
Key Features:
- 56KHz Ultrasonic Wave: High-frequency vibration for thorough cleaning.
- 3-in-1 Design: Includes built-in tweezers, a suction stick, and a mirror.
- Independent Cleaning Chamber: Dedicated compartment for contact lens solution.
- One-Touch Operation: Simple start with a single button.
- Quick Charging: USB charging with up to 20 days standby time.
- Portable: Compact and lightweight for travel.
Components:
The device includes the main cleaning unit, a USB charging cable, and a storage pouch.
Image: The interior of the EraClean GM02 device, showing the separate compartments for contact lenses and the integrated tweezers and suction stick.
Image: A complete view of the EraClean GM02 package contents, including the cleaner, USB cable, and storage pouch.
3. Setup
Charging the Device:
- Locate the USB charging port on the side of the EraClean GM02.
- Connect the provided USB cable to the device and plug the other end into a compatible USB power source (e.g., wall adapter, computer USB port).
- The device will indicate charging status (e.g., an indicator light). A full charge takes approximately 2 hours and provides up to 20 days of standby time.
Image: The EraClean GM02 device connected to a USB cable for charging, illustrating the charging port location.
4. Operating Instructions
Follow these steps for effective cleaning of your contact lenses:
- Open the Cover: Gently open the lid of the EraClean GM02 device.
- Place Lenses: Using the built-in tweezers or suction stick, carefully place your contact lenses into their respective cleaning chambers.
- Add Solution: Fill the cleaning chambers with fresh contact lens care solution until the lenses are completely submerged.
- Close Cover: Close the lid securely.
- Start Cleaning: Press the power button (one-touch switch) to begin the ultrasonic cleaning cycle. The cycle typically lasts 3 minutes.
- Retrieve Lenses: Once the cycle is complete, open the lid and use the tweezers or suction stick to carefully remove your clean contact lenses. Discard the used solution.
Image: A visual step-by-step guide demonstrating how to open the cleaner, insert lenses, add solution, close the lid, and start the cleaning process.
Demonstration Video:
Video: An official product video demonstrating the features and operation of the EraClean GM02 Ultrasonic Contact Lens Cleaner, including how to place lenses, add solution, and activate the cleaning cycle.
5. Maintenance
Cleaning the Device:
- After each use, empty any remaining solution from the cleaning chambers.
- Wipe the interior and exterior of the device with a clean, soft cloth.
- Do not use abrasive cleaners or harsh chemicals, as these can damage the device.
- Ensure the device is dry before closing the lid for storage.
Care for Accessories:
- Rinse the tweezers and suction stick with fresh contact lens solution or sterile saline after each use.
- Store accessories within their designated compartments inside the cleaner to keep them clean and prevent loss.
Image: The EraClean GM02 device with water droplets, illustrating its waterproof design for easy cleaning and durability.
6. Troubleshooting
Device Not Turning On:
- Check Battery: Ensure the device is sufficiently charged. Connect it to a USB power source and allow it to charge for at least 30 minutes before attempting to use it again.
- Verify Connection: Make sure the USB cable is securely connected to both the device and the power source.
Lenses Not Feeling Clean:
- Proper Solution Level: Ensure the contact lenses are fully submerged in fresh contact lens solution during the cleaning cycle.
- Solution Type: Use only recommended contact lens care solutions. Do not use tap water or other liquids.
- Cycle Duration: Confirm the device completes its full 3-minute cleaning cycle.
Image: A comparison showing a contact lens before and after cleaning, highlighting the removal of impurities by the EraClean GM02.
7. Specifications
| Product Dimensions | 3.93 x 2.36 x 1.38 inches |
| Item Weight | 9.77 ounces |
| Model Number | GM02 |
| Manufacturer | EraClean |
| Ultrasonic Frequency | 56KHz |
| Charging Time | Approx. 2 hours |
| Standby Time | Up to 20 days |
8. Safety Information
Please observe the following safety guidelines:
- Always follow the instructions provided with the product.
- Keep out of reach of children.
- Do not use if the seal is broken or missing.
- Avoid contact with eyes. If contact occurs, rinse immediately with plenty of water and seek medical advice.
- Do not use after the expiration date of your contact lens solution.
- Dispose of the product and its packaging in accordance with local, state, and federal regulations.
- Statements regarding dietary supplements have not been evaluated by the FDA and are not intended to diagnose, treat, cure, or prevent any disease or health condition. (Note: This statement appears in the provided product data under 'ingredients' and is included for completeness, though it may not directly apply to the cleaner itself.)
9. Warranty and Support
EraClean provides a 12-month warranty for this product. For any questions or assistance, please contact EraClean customer service. We offer 24-hour customer support to address your concerns.
