Craftride 1" Handlebar Riser User Manual

Introduction

This manual provides essential information for the installation, maintenance, and safe use of your Craftride 1" Handlebar Riser. Please read these instructions carefully before installation to ensure proper fitment and operation. These risers are designed to raise and pull back your motorcycle's handlebars, improving riding posture and comfort.

Product Overview

The Craftride Handlebar Riser set consists of two chrome-plated alloy risers designed for 1" (25.4mm) handlebars. They are engineered to raise the handlebar by 4.5 inches (115mm) and bring the handlebar position 1.5 inches (38mm) closer to the rider.

Figure 1: Front view of the Craftride 1" Handlebar Risers. These risers feature a polished chrome finish and are designed to elevate and reposition the handlebars for improved rider ergonomics.

Figure 2: Bottom view of the Craftride 1" Handlebar Risers. This perspective highlights the mounting holes at the base of each riser, which are designed to secure the risers to the motorcycle's triple tree.

Setup and Installation

Installation of handlebar risers requires mechanical aptitude. If you are unsure about any step, it is recommended to seek professional assistance. Always ensure the motorcycle is stable and secure before beginning work.

Important Considerations:

• Cable and Line Length: It is crucial to check if an extension of the clutch cable, brake line, throttle cables, and electrical wiring is necessary due to the increased handlebar height and pullback. Insufficient cable length can lead to dangerous situations.
• Universal Fit: This is a universal article. The listed compatible models are examples only. Before purchase and installation, carefully check the dimensions of these risers against your motorcycle's existing setup to ensure proper fitment.
• Potential Modifications: Depending on your specific motorcycle model, minor modifications or adjustments may be necessary for a secure and safe installation.

Figure 3: Detailed dimensions of the handlebar riser. Key measurements include height (15.30cm / 6.0in), width (3.1cm / 1.2in), depth (4.9cm / 1.92in), handlebar hole diameter (2.5cm / 1.0in), and bottom hole diameter (12mm).

General Installation Steps (Consult your motorcycle's service manual for specific torque values and procedures):

1. Secure the motorcycle on a stable stand.
2. Carefully remove the existing handlebar clamps and handlebars. Support the handlebars to prevent damage to attached components.
3. Inspect the mounting area on the triple tree for cleanliness and any obstructions.
4. Place the new Craftride handlebar risers onto the triple tree mounting points. Ensure they are correctly oriented.
5. Secure the risers using appropriate bolts and washers. Tighten fasteners to the manufacturer's specified torque values.
6. Reinstall the handlebars into the new risers. Ensure the handlebars are centered and at the desired angle.
7. Secure the handlebar clamps onto the risers, tightening fasteners evenly and to specified torque values.
8. Carefully re-route and re-attach all cables, lines, and wiring. Verify that there is sufficient slack for full steering lock in both directions without binding or stretching.
9. Test all controls (brakes, clutch, throttle, switches) for proper function and smooth operation.
10. Perform a static check of the steering from lock to lock to ensure no cables or lines are pinched or stretched.

Operating

Once properly installed, the handlebar risers become an integral part of your motorcycle's steering system. No specific operational procedures are required beyond standard motorcycle operation. Always ensure all fasteners are secure before riding.

Maintenance

To ensure the longevity and safety of your Craftride handlebar risers:

• Regular Inspection: Periodically check all mounting bolts for tightness, especially after the first few rides following installation. Vibrations can loosen fasteners over time.
• Cleaning: Clean the risers with a soft cloth and mild, non-abrasive cleaner. Avoid harsh chemicals that could damage the chrome finish.
• Damage Check: Inspect the risers for any signs of damage, cracks, or corrosion. If damage is found, replace the risers immediately.

Troubleshooting

If you encounter issues after installing the handlebar risers, consider the following:

• Cables/Lines Too Short: If controls are stiff, binding, or preventing full steering lock, the cables, lines, or wiring are likely too short. This requires replacement with longer components. Do not ride the motorcycle until this is resolved.
• Handlebar Movement/Play: Re-check all mounting bolts for the risers and handlebar clamps. Ensure they are tightened to the correct torque specifications.
• Vibration: Excessive vibration might indicate loose fasteners or improper installation. Re-check all connections.
• Fitment Issues: If the risers do not fit correctly on your motorcycle, double-check the dimensions against your motorcycle's specifications. As a universal part, some motorcycles may not be compatible without significant modification.

Specifications

Warranty and Support

Specific warranty information for this product is not provided in the available documentation. For any warranty claims, technical support, or further inquiries, please contact the manufacturer, Craftride, or your point of purchase directly. Always retain your proof of purchase.