AZH Evaporator Fan Motor Replacement for Kenmore Refrigerators

Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your new AZH Evaporator Fan Motor Replacement. This part is designed to be compatible with various Kenmore refrigerator models, including 106.72152110, 106.72159111, 106.72152111, 106.72153111, 106.72154110, 106.72154111, 106.72159110, 106.72159111, 106.72163110, 106.73202300, and 106.73203300. Please read this manual thoroughly before attempting any installation or repair to ensure safe and correct usage.

Safety Information

WARNING: Risk of Electric Shock and Injury.

• Always disconnect power to the refrigerator before attempting any repairs or installation. Failure to do so can result in serious injury or death.
• Wear appropriate personal protective equipment, such as gloves, to prevent cuts or scrapes.
• If you are unsure about any step of the installation process, consult a qualified appliance repair technician.
• Keep small parts away from children.

Package Contents

Your package should contain the following item:

• 1 x AZH Evaporator Fan Motor Replacement

Image: A close-up view of the AZH Evaporator Fan Motor Replacement. The motor is black with a gray base, featuring two electrical wires ending in a white connector, and a metal shaft extending from the motor housing.

Setup (Installation)

This section outlines the general steps for replacing an evaporator fan motor. Specific refrigerator models may have slight variations. Refer to your refrigerator's service manual for precise instructions if available.

1. Disconnect Power: Unplug the refrigerator from the electrical outlet or turn off the circuit breaker supplying power to the appliance.
2. Access Freezer Compartment: Open the freezer door. You may need to remove shelves, ice maker components, or other obstructions to gain access to the rear panel of the freezer compartment.
3. Remove Evaporator Cover: Locate the evaporator cover, typically at the back of the freezer. This cover is usually secured by screws. Carefully remove the screws and detach the cover. The evaporator fan motor is usually mounted behind this cover.
4. Disconnect Old Motor: Before removing the old motor, disconnect its electrical connector. Note the orientation of the wires if they are not color-coded or if there are multiple connections.
5. Remove Old Fan Blade: The fan blade is typically pressed onto the motor shaft. Gently pull or pry the fan blade off the old motor shaft. Be careful not to damage the blade.
6. Remove Old Motor: Unscrew or unclip the old evaporator fan motor from its mounting bracket.
7. Install New Motor: Mount the new AZH Evaporator Fan Motor Replacement onto the bracket, securing it with the original screws or clips.
8. Attach Fan Blade: Carefully press the existing fan blade onto the shaft of the new motor. Ensure it is seated correctly and spins freely without hitting any obstructions.
9. Reconnect Electrical: Connect the electrical connector to the new motor. Ensure a secure connection.
10. Reassemble: Reattach the evaporator cover, securing it with screws. Replace any shelves, ice maker components, or other parts that were removed.
11. Restore Power: Plug the refrigerator back into the electrical outlet or turn on the circuit breaker.

Operating

After installation, the refrigerator should begin to cool normally. The evaporator fan motor circulates air over the evaporator coils to cool the freezer and refrigerator compartments. You should hear the fan operating when the compressor is running.

• Allow several hours for the refrigerator to reach its set temperature after installation.
• Listen for any unusual noises from the freezer compartment. The fan should operate smoothly.

Maintenance

The AZH Evaporator Fan Motor Replacement is designed for durability and typically requires minimal maintenance. However, regular cleaning of the refrigerator's condenser coils can help maintain overall appliance efficiency and reduce strain on all components, including the fan motor.

• Ensure the refrigerator's vents are not blocked by food items, which can impede airflow and overwork the fan.
• Periodically check for ice buildup around the evaporator coils, which can obstruct the fan blade. If excessive ice is present, defrost the refrigerator.

Troubleshooting

If you experience issues after replacing the evaporator fan motor, consider the following common troubleshooting steps:

• Fan Not Running:
  • Check if the refrigerator is plugged in and receiving power.
  • Ensure the electrical connector to the motor is securely attached.
  • Verify that the freezer door switch is functioning correctly (the fan often stops when the door is open).
• Unusual Noises:
  • Disconnect power and check if the fan blade is hitting any ice buildup or other obstructions.
  • Ensure the fan blade is securely attached to the motor shaft.
  • Verify the motor is securely mounted and not vibrating against other components.
• Insufficient Cooling:
  • Confirm the fan is running when the compressor is active.
  • Check for excessive frost buildup on the evaporator coils, which can indicate a defrost system issue, not necessarily the fan motor.
  • Ensure refrigerator vents are clear.

If these steps do not resolve the issue, it is recommended to contact a qualified appliance repair technician.

Specifications

Warranty and Support

For warranty information regarding your AZH Evaporator Fan Motor Replacement, please refer to the documentation provided at the time of purchase or contact the seller directly. Specific warranty terms may vary.

For technical support or further assistance, please contact the manufacturer, AZH, through their official support channels. Contact information can typically be found on the product packaging or the seller's website.