Mintu 110.27082601

Mintu Suspension Rod Kit Replacement Manual

For Kenmore, Maytag, and Whirlpool Washing Machines

Model: 110.27082601 (and compatible models)

1. Introduction

This instruction manual provides comprehensive guidance for the installation, operation, maintenance, and troubleshooting of the Mintu Suspension Rod Kit. This kit is designed to replace worn or damaged suspension rods in various top-load washing machines, restoring balance and reducing excessive vibration during operation. Please read this manual thoroughly before beginning any installation or repair work.

2. Safety Information

Always prioritize safety when working with appliances. Failure to follow these safety instructions may result in personal injury or damage to the appliance.

  • Disconnect Power: Before performing any service or maintenance, always unplug the washing machine from its power source or turn off the circuit breaker.
  • Wear Protective Gear: Wear work gloves to protect your hands from sharp edges and safety glasses to protect your eyes.
  • Two-Person Lift: The washing machine tub can be heavy. Enlist assistance when lifting or moving heavy components to prevent injury.
  • Proper Tools: Use appropriate tools for the job to avoid damaging parts or causing injury.
  • Professional Assistance: If you are unsure about any step, consult a qualified appliance repair technician.

3. Package Contents

The Mintu Suspension Rod Kit typically includes the following components:

  • 4 x Suspension Rods (metal rods with springs and plastic components)
  • 4 x Upper Support Balls (white plastic, for the top of the rods)
  • 4 x Lower Support Bushings (white plastic, for the bottom of the rods)
Mintu Suspension Rod Kit showing four complete suspension rods and eight loose white plastic components
Image 3.1: Complete Mintu Suspension Rod Kit. This image displays four assembled suspension rods, each consisting of a black metal rod, a spring, and blue and white plastic components. Additionally, eight loose white plastic components (four upper support balls and four lower support bushings) are shown at the top of the image.
Close-up of a single Mintu suspension rod assembly
Image 3.2: Detailed view of a single suspension rod assembly. This close-up shows the black metal rod, the coiled spring, a blue plastic cap, and white plastic components that make up one complete suspension rod.

4. Compatible Models

This Mintu Suspension Rod Kit is compatible with a wide range of Kenmore, Maytag, and Whirlpool washing machine models. Please verify your washing machine's model number against the list below to ensure compatibility. This list is not exhaustive; if your model is not listed, please cross-reference with your appliance's parts diagram.

Kenmore Models:

  • 110.27032600, 110.27032601, 110.27032602, 110.27032603
  • 110.27042600, 110.27042601, 110.27042602, 110.27042603
  • 110.27052600, 110.27052601, 110.27052602
  • 110.27062600, 110.27062601, 110.27062602, 110.27062603, 110.27062604
  • 110.27072600, 110.27072601, 110.27072602, 110.27072603, 110.27072604
  • 110.27082600, 110.27082601, 110.27082602, 110.27082603, 110.27082604, 110.27082605
  • 110.27086601, 110.27086602, 110.27086603, 110.27086604, 110.27086605
  • 110.27087600, 110.27087601, 110.27087602, 110.27087603, 110.27087604, 110.27087605
  • 110.27092600, 110.27092601, 110.27092602, 110.27092603
  • 110.27152600, 110.27152601, 110.27152602
  • 110.28032700, 110.28032701
  • 110.28042700, 110.28042701
  • 110.28062800, 110.28072800, 110.28081700, 110.28082700, 110.28087700
  • 110.28091700, 110.28092700, 110.28097700, 110.28132410

Maytag Models:

  • MTW6300TQ0, MTW6300TQ1, MTW6400TQ0, MTW6500TQ0
  • MTW6600TB0, MTW6600TB1, MTW6600TQ0, MTW6600TQ1
  • MTW6700TQ0, MTW6700TQ1
  • MVWB400VQ0, MVWB700VQ0, MVWB800VB0, MVWB800VQ0, MVWB800VU0

Whirlpool Models:

  • WTW6200SW0, WTW6200SW1, WTW6200SW2, WTW6200SW3, WTW6200VW0
  • WTW6300SB0, WTW6300SB1, WTW6300SB2, WTW6300SG0, WTW6300SG1, WTW6300SG2
  • WTW6300SW0, WTW6300SW1, WTW6300SW2
  • WTW6400SW0, WTW6400SW1, WTW6400SW2, WTW6400SW3
  • WTW6600SB0, WTW6600SB1, WTW6600SB2, WTW6600SB3
  • WTW6600SG0, WTW6600SG1, WTW6600SG2, WTW6600SG3
  • WTW6600SW0, WTW6600SW1, WTW6600SW2, WTW6600SW3
  • WTW6700TU1, WTW6700TU2, WTW6700TW0, WTW6700TW1, WTW6700TW2

5. Installation / Setup

Follow these steps carefully to replace the suspension rods in your washing machine. The exact procedure may vary slightly depending on your specific model, but the general steps remain consistent.

Tools Required:

  • Screwdriver (Phillips or flathead, depending on your model)
  • Work Gloves
  • Safety Glasses

Step-by-Step Installation:

  1. Disconnect Power: Unplug the washing machine from the electrical outlet. This is a critical safety step.
  2. Access the Tub: Depending on your washer model, you may need to remove the control panel and/or the top lid of the washing machine to gain access to the tub and suspension rods. Typically, there are screws at the back of the control panel or clips under the front lip of the top panel.
  3. Identify Old Rods: Locate the four suspension rods that support the washing machine tub. They are usually positioned at each corner of the tub.
  4. Remove Old Rods:
    • Carefully lift the tub slightly to relieve tension on the rods.
    • At the top, unhook the rod from the washer frame. The upper support ball will likely come off with the rod.
    • At the bottom, gently pull the rod out of the lower support bushing located on the tub.
    • Repeat for all four rods.
    Close-up of the hook end of a suspension rod
    Image 5.1: Detail of the suspension rod's hook end. This image shows the curved metal hook designed to attach to the washing machine frame, along with the plastic components near the top of the rod.
  5. Install New Rods:
    • Ensure the new lower support bushing is correctly seated in the tub's mounting point.
    • Insert the bottom end of a new suspension rod into the lower support bushing on the tub.
    • Attach the upper support ball to the top of the rod.
    • Hook the top end of the rod (with the upper support ball) onto the washer frame. Ensure it is securely seated.
    • Repeat for all four new rods. It is recommended to replace all four rods simultaneously for optimal balance.
    Close-up of a single Mintu suspension rod assembly, showing the spring and plastic components
    Image 5.2: Another detailed view of a suspension rod. This image highlights the spring mechanism and the blue and white plastic components that facilitate the rod's movement and support.
    Close-up of the white plastic upper support balls and lower support bushings
    Image 5.3: Close-up of the white plastic components. This image shows the individual upper support balls and lower support bushings, which are crucial for the proper functioning and smooth movement of the suspension rods.
  6. Reassemble Washer: Reattach the top lid and control panel, ensuring all screws and clips are securely fastened.
  7. Test Operation: Plug the washing machine back into the electrical outlet. Run a small, empty load cycle to check for proper balance and reduced vibration.

6. Operating Principle

The suspension rods are a critical component in top-load washing machines. They support the wash tub and dampen its movement during the wash and spin cycles. Each rod consists of a metal shaft, a spring, and plastic components that allow the tub to move freely while absorbing vibrations and preventing it from hitting the outer cabinet. When functioning correctly, they ensure the tub remains balanced, especially during high-speed spinning, leading to quieter operation and preventing damage to the machine.

7. Maintenance

While suspension rods are designed for durability, periodic inspection can help identify potential issues before they become major problems.

  • Visual Inspection: Annually, or if you notice increased vibration, remove the washer's top panel (following safety guidelines) and visually inspect the rods. Look for signs of wear, corrosion, or damage to the plastic components.
  • Cleanliness: Keep the area around the suspension rods free from lint, debris, or detergent residue, which could impede their movement.
  • Load Balance: Always load your washing machine evenly. Overloading or uneven loading can put excessive stress on the suspension system, leading to premature wear.

8. Troubleshooting

If your washing machine exhibits any of the following symptoms, it may indicate that the suspension rods need replacement:

  • Excessive Vibration: The most common symptom. The washer shakes violently, especially during the spin cycle.
  • Loud Banging Noises: The tub may hit the sides of the washer cabinet during operation.
  • Washer Moving: The appliance 'walks' or moves significantly from its original position during a cycle.
  • Off-Balance Error Codes: Some modern washers may display an error code related to an unbalanced load, even when the load is properly distributed.
  • Tub Sagging: The wash tub appears to sit lower than usual or is visibly uneven.

If you experience these issues, inspect the suspension rods as described in the maintenance section. If wear or damage is evident, proceed with replacement.

9. Specifications

  • Product Type: Washing Machine Suspension Rod Kit
  • Brand: Mintu
  • Material: Metal (rods), Durable Plastic (bushings, caps)
  • Quantity: 4 Suspension Rods, 4 Upper Support Balls, 4 Lower Support Bushings
  • Compatibility: Kenmore, Maytag, Whirlpool top-load washing machines (refer to Section 4 for specific models)

10. Warranty and Support

For information regarding product warranty, returns, or technical support, please refer to the retailer's policy where the product was purchased or visit the official Mintu brand store online. Keep your purchase receipt as proof of purchase.

Thank you for choosing Mintu products.