Introduction
This manual provides instructions for the proper use and maintenance of your Tecasa Microfiber Cloths, designed as a replacement kit for the Cecotec Conga WinRobot 870 window cleaning robot. This kit includes 16 high-quality microfiber cloths to ensure optimal cleaning performance.

Image: A pack of 16 Tecasa microfiber cloths, designed for the Conga WinRobot 870. The cloths are white and rectangular, shown neatly stacked.
Setup and Installation
To install the microfiber cloths on your Cecotec Conga WinRobot 870, follow these steps:
- Ensure the window cleaning robot is powered off and disconnected from any power source.
- Locate the designated attachment areas on the underside of the robot where the cleaning cloths are secured.
- Remove any old or worn cloths by detaching them from the robot's fastening mechanism (e.g., Velcro or clips).
- Align a new Tecasa microfiber cloth with the attachment area. Ensure the cloth is spread flat and covers the entire cleaning surface.
- Securely attach the new cloth, making sure it is firmly in place and will not detach during operation.
- Repeat the process for all required cleaning pads on the robot.

Image: A close-up view of a white microfiber cloth being attached to the base of a window cleaning robot. The cloth is being pressed onto a fastening surface.
Operating Instructions
The Tecasa microfiber cloths support two primary cleaning modes with your Conga WinRobot 870:
- Dry Cleaning: For light dust and polishing, attach dry cloths to the robot. This mode is suitable for maintaining clean surfaces.
- Wet Cleaning: For more thorough cleaning and removing stubborn dirt, slightly dampen the cloths with water or a specific window cleaning solution before attaching them to the robot. Ensure the cloths are not oversaturated to prevent dripping.
Always refer to your Cecotec Conga WinRobot 870's main instruction manual for specific operating procedures and safety guidelines.
Maintenance and Care
Proper maintenance of your microfiber cloths will extend their lifespan and ensure effective cleaning:
- Washing: The Tecasa microfiber cloths are fully washable. After each use, remove the cloths from the robot and wash them. They can be hand-washed or machine-washed with similar colors. Avoid using fabric softeners, as they can reduce the microfiber's effectiveness.
- Drying: Air dry the cloths or tumble dry on a low heat setting. Do not iron.
- Replacement: The lifespan of the cleaning cloths depends on their frequency of use and cleaning conditions. Generally, cloths should be replaced when they show signs of significant wear, tear, or when their cleaning performance noticeably diminishes. This kit provides 16 cloths for multiple replacements.
Troubleshooting
If you experience reduced cleaning performance with your robot, consider the following:
- Poor Cleaning Results: Ensure the microfiber cloths are clean and free from excessive dirt or debris. If they are heavily soiled or worn, replace them with fresh cloths.
- Cloths Detaching: Verify that the cloths are securely attached to the robot's fastening mechanism before operation.
- Streaks on Windows: For wet cleaning, ensure cloths are not oversaturated. Use an appropriate, streak-free window cleaning solution. If streaks persist, the cloths might be worn out and require replacement.
For issues related to the robot's operation, refer to the Cecotec Conga WinRobot 870's instruction manual.
Product Specifications
| Brand | Tecasa |
| Product Type | Microfiber Replacement Cloths |
| Quantity | 16 cloths per pack |
| Compatibility | Cecotec Conga WinRobot 870 Window Cleaning Robot |
| Material | Microfiber |
| ASIN | B09G3B53YP |
Warranty and Support
Information regarding specific product warranty for these Tecasa Microfiber Cloths is not included in this manual. For warranty details or product support, please contact the retailer where the product was purchased or refer to the official Tecasa website if available. Please note that spare parts availability information is currently unavailable.