TooCust End Table with Charging Station (Set of 2) User Manual

Introduction

This manual provides essential information for the assembly, operation, and maintenance of your TooCust End Table with Charging Station. Please read these instructions carefully before assembly and use to ensure safe and proper functionality.

Image: Overview of the TooCust End Tables with integrated charging functionality.

Safety Information

WARNING: Failure to follow these safety instructions may result in injury or damage to the product.

• Always assemble according to the provided instructions.
• Do not overload the table. The maximum weight recommendation for the tabletop is 150 lbs.
• Keep fingers clear of the flip-top drawer mechanism when opening or closing to prevent pinching.
• Ensure all electrical connections are secure and the power cord is not pinched or damaged.
• Do not expose the charging station to liquids.
• Supervise children when they are near or interacting with the table.
• This product is intended for indoor use only.

Package Contents

Verify that all components are present before beginning assembly. If any parts are missing or damaged, please contact customer support.

• Tabletop with Flip-Top Drawer and Integrated Charging Station
• X-Shaped Metal Frame Components
• Lower Shelf
• Adjustable Metal Foot Pads
• Assembly Hardware (screws, bolts, etc.)
• Installation Tool (Wrench)
• Instruction Manual

Assembly Instructions

Assembly typically takes approximately 20 minutes. Follow these steps carefully:

1. Unpack Components: Carefully remove all parts from the packaging. Lay them out on a clean, soft surface to prevent scratches. Verify all parts against the package contents list.
2. Attach X-Shaped Frames: Secure the X-shaped metal frame components to the main table structure using the provided hardware. Ensure all screws are finger-tight at this stage.
3. Install Lower Shelf: Position the lower shelf between the metal frames and secure it with the appropriate screws.
4. Attach Adjustable Foot Pads: Screw the adjustable metal foot pads into the bottom of each leg. These can be adjusted later to level the table on uneven surfaces.
5. Tighten All Hardware: Once all components are in place, systematically tighten all screws and bolts using the provided wrench. Do not overtighten.
6. Inspect Stability: Gently shake the assembled table to ensure it is stable. Adjust foot pads as needed to eliminate wobbling.

Image: Detailed view of key components including adjustable feet, flip hinge, and charging station.

Operating Instructions

Using the Charging Station

The integrated charging station provides convenient power access for your devices.

• Connect Power: Plug the table's power cord into a standard 120V AC wall outlet.
• Access Charging Ports: Lift the flip-top lid to reveal the charging station, which includes 2 standard AC outlets and 2 USB ports.
• Charge Devices: Plug your devices into the appropriate AC outlet or USB port. The thoughtful design includes grooves on both sides of the flip-top compartment, allowing charging cables to exit from either the left or right side, even when the lid is closed.

Image: The flip-top compartment with integrated charging station in use.

Using the Flip-Top Storage

The 5.5-inch deep flip-top compartment offers discreet storage for various items.

• Open: Gently lift the front edge of the tabletop to open the flip-top.
• Store Items: Place small items such as remote controls, books, or personal devices inside the compartment.
• Close: Carefully lower the flip-top until it is flush with the table surface. Ensure no cables are pinched.

Maintenance

• Cleaning: Wipe the table surfaces with a dry, soft cloth. Avoid abrasive cleaners or harsh chemicals that may damage the finish.
• Spills: In case of spills, wipe immediately with a dry cloth. Do not allow liquids to enter the charging station.
• Hardware Check: Periodically check all screws and bolts to ensure they remain tight. Retighten if necessary.
• Placement: Avoid placing the table in direct sunlight or near heat sources to prevent material degradation.

Troubleshooting

• Table Wobbles: Adjust the individual metal foot pads at the bottom of each leg until the table is stable on uneven surfaces.
• Charging Station Not Working:
  • Ensure the main power cord is securely plugged into a functional wall outlet.
  • Check if the device you are trying to charge is properly connected to the AC outlet or USB port.
  • Test the wall outlet with another appliance to confirm it is receiving power.
• Loose Components After Assembly: Re-check and tighten all assembly hardware. If dowels feel loose, ensure they are fully inserted and consider re-assembling with attention to secure connections.

Specifications

Image: Detailed product dimensions and weight capacities.

Warranty and Support

TooCust products are designed for quality and durability. For any questions, missing parts, or support needs, please contact TooCust customer service. Please retain your proof of purchase for warranty claims.

For further assistance, visit the official TooCust store on Amazon: TooCust Store