1. Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your MAIDESITE Electric Standing Desk, Model JP-02. Please read this manual thoroughly before assembly and use to ensure proper function and safety.
Image 1.1: The MAIDESITE Electric Standing Desk in a typical office environment.
2. Safety Information
- Ensure all components are present and undamaged before assembly. Do not use if any parts are missing or broken.
- Assembly should ideally be performed by two adults due to the weight of the components.
- Keep children and pets away from the desk during operation to prevent injury.
- Do not overload the desk. The maximum load capacity is 80 kg.
- Ensure there are no obstacles in the desk's path during height adjustment. The desk features a collision detection system, but caution is advised.
- Use only the provided power adapter.
- Do not attempt to disassemble or repair the motor or control unit yourself. Contact customer support for assistance.
3. Package Contents
Your MAIDESITE Electric Standing Desk package includes the following main components:
- Desk Legs (Frame)
- Desk Top Plate (120 x 60 x 2.5 cm)
- Control Panel with USB Port
- Power Adapter and Cable
- Assembly Hardware (screws, tools, etc.)
- User Manual (this document)
Please verify all parts are present before beginning assembly. If any parts are missing, contact customer support.
4. Assembly Instructions
Assembly of the MAIDESITE Electric Standing Desk requires careful attention to detail. It is recommended to have two people for assembly, especially when handling the heavy desk top and frame.
4.1 Tools Required
- Phillips Head Screwdriver (electric screwdriver recommended)
- Level (optional, for final adjustment)
4.2 Assembly Steps
- Unpack all components and lay them out on a clean, soft surface to prevent scratches.
- Attach the desk legs to the crossbar according to the included diagram. Ensure all bolts are securely tightened.
- Mount the control box to the designated area on the desk frame.
- Connect the motor cables and control panel cable to the control box. Ensure connections are firm.
- Carefully place the desk top plate upside down on the soft surface.
- Align the assembled desk frame with the pre-drilled holes on the underside of the desk top.
- Secure the desk frame to the top plate using the provided screws. Ensure the screws are tightened firmly but do not overtighten.
- Attach the control panel to the front edge of the desk top.
- Carefully flip the desk upright. This step is best done with two people.
- Install the adjustable feet (adjusters) at the bottom of the desk legs. Adjust them to ensure the desk is level.
For visual guidance, please refer to the assembly video available on the product page or manufacturer's website.
5. Operating Instructions
5.1 Control Panel Overview
Image 5.1: The control panel features an LED display, height adjustment buttons, memory presets, and a USB charging port.
The control panel allows you to adjust the desk height, save preferred positions, and access other functions. It includes an LED display showing the current height in centimeters.
5.2 Height Adjustment
- Press the Up (▲) button to raise the desk.
- Press the Down (▼) button to lower the desk.
- Release the button at your desired height. The desk can adjust between 62 cm and 125 cm.
Image 5.2: The desk offers a wide height adjustment range from 62 cm to 125 cm.
5.3 Memory Presets
The desk allows you to save up to four preferred height positions for quick adjustment.
- Adjust the desk to your desired height using the Up/Down buttons.
- Press the SET button. The LED display will show 'S-'.
- Within 3 seconds, press one of the memory buttons (1, 2, 3, or 4) to save the current height to that preset. The display will show 'S-1', 'S-2', etc., to confirm.
- To recall a saved height, simply press the corresponding memory button (1, 2, 3, or 4). The desk will automatically move to the saved position.
Image 5.3: The control panel allows saving and recalling four distinct height settings.
5.4 Collision Detection Function
The desk is equipped with a collision detection system. If an obstacle is encountered during height adjustment, the desk will automatically stop and reverse its movement by approximately 3-4 cm to prevent damage or injury.
Image 5.4: The desk's collision detection system enhances safety during operation.
5.5 Sedentary Alarm Function
To encourage movement and prevent prolonged sitting, the desk includes a sedentary alarm.
- Press the Alarm (bell icon) button to cycle through alarm settings: 0.5h, 1h, 2h, or Off.
- When an alarm time is set, the motor will vibrate to remind you to change your posture (e.g., from sitting to standing).
Image 5.5: The sedentary alarm reminds users to alternate between sitting and standing positions.
5.6 Lock Function
To prevent accidental operation, especially by children, the control panel features a lock function.
- Press and hold the Lock (padlock icon) button for 3 seconds to activate or deactivate the lock.
- When locked, the LED display will show 'LOC', and no buttons will respond.
5.7 USB Charging Port
A USB charging port is integrated into the side of the control panel for convenient charging of your electronic devices.
Image 5.6: The control panel includes a USB port for charging devices.
6. Maintenance
- Regularly check all screws and bolts to ensure they are tight. Retighten if necessary.
- Clean the desk surface with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals.
- The melamine top plate is resistant to scratches, dirt, moisture, and heat, but it is still recommended to use coasters for drinks and avoid placing extremely hot items directly on the surface.
- Keep the motor and electrical components free from dust and moisture.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Desk does not move. | Power cable disconnected, control panel locked, motor error. | Check power connections. Unlock the control panel (press and hold lock button for 3s). Perform a system reset (refer to manufacturer's video or contact support). |
| Desk moves unevenly or makes unusual noise. | Uneven load, loose connections, motor issue. | Ensure weight is evenly distributed. Check all assembly bolts for tightness. Contact customer support if the issue persists. |
| Collision detection triggers too easily or not at all. | Sensitivity setting, obstruction. | Ensure no constant pressure or light obstruction is present. Contact customer support for sensitivity adjustment if available. |
| Cannot save memory presets. | Incorrect procedure. | Follow the memory preset instructions carefully (Section 5.3). Ensure you press the memory button within 3 seconds after pressing SET. |
8. Specifications
| Feature | Specification |
|---|---|
| Model | JP-02 |
| Desk Top Dimensions (L x W x H) | 120 cm x 60 cm x 2.5 cm |
| Height Adjustment Range | 62 cm - 125 cm |
| Lifting Speed | 32 mm/s |
| Load Capacity | 80 kg |
| Noise Level | < 50 dB |
| Desk Top Material | Melamine Resin Laminated Alloy Steel |
| Frame Material | SPCC Steel |
| Features | 4 Memory Presets, Collision Detection, Lock Function, Sedentary Alarm, USB Charging Port |
| Assembly Required | Yes |
9. Warranty and Support
9.1 Manufacturer's Warranty
The MAIDESITE Electric Standing Desk comes with a 5-year manufacturer's warranty. This warranty covers defects in materials and workmanship under normal use.
9.2 Customer Support
If you encounter any issues, have questions, or require assistance with missing parts or malfunctions, please do not hesitate to contact our customer support team.
Email: amzservicejp1@maidesite.com
Please provide your model number (JP-02) and a detailed description of the issue when contacting support to ensure a prompt resolution.