INALSA Homeasy WD10 Wet and Dry Vacuum Cleaner

1. Product Overview

The INALSA Homeasy WD10 is a versatile wet and dry vacuum cleaner designed for various cleaning tasks. It features a powerful 1200W motor, a 10-liter capacity tank, and a blower function for efficient cleaning.

Image 1.1: Overview of the INALSA Homeasy WD10 vacuum cleaner with key components labeled, including the blower function port, easy carry handle, secure latch system, on/off switch, 10L tank capacity, on-board tool storage, and swivel caster wheels.

2. Safety Instructions

Before operating the appliance, please read all safety instructions carefully to prevent electric shock, fire, or injury.

• Ensure the power supply voltage matches the rating label on the appliance.
• Do not use the vacuum cleaner to pick up flammable or combustible liquids, hot ashes, or sharp objects.
• Always unplug the appliance from the power outlet before cleaning or performing maintenance.
• Keep hands, feet, loose clothing, and hair away from rotating parts.
• Do not immerse the motor unit in water or other liquids.
• This appliance is for indoor use only.

3. Assembly and Setup

Follow these steps to assemble your vacuum cleaner before first use.

3.1 Unpacking and Component Identification

Carefully remove all components from the packaging. Verify that all parts listed below are present:

• 1N Container
• 1N Motor Unit
• 1N Hose Pipe with Handle Grip
• 3N Extension Pipes
• 1N Dry & Wet Squeezing Brush
• 1N 2-in-1 Crevice Nozzle
• 1N Small Round Brush
• 2N Cloth Filters (for dry use)
• 1N Sponge Filter (for wet use)
• 1N Carry Handle
• 2N Handle Screws
• 1N Filter Holder Ring
• 4N Castor Wheels
• 1N Instruction Manual cum Warranty Card

Image 3.1: All included accessories: Wet & Dry Brush, Extension Rods, Crevice Nozzle, Cloth Filter, Sponge Filter, Flexible Hose, and Small Round Brush.

3.2 Attaching Castor Wheels

1. Turn the container upside down.
2. Insert each of the four castor wheels into the designated slots on the base of the container until they click into place.

3.3 Installing the Carry Handle

1. Align the carry handle with the slots on the motor unit.
2. Secure the handle using the provided handle screws.

3.4 Filter Installation

The type of filter used depends on whether you are performing wet or dry cleaning.

• For Dry Cleaning: Place one of the cloth filters over the motor unit's filter cage. Secure it with the filter holder ring.
• For Wet Cleaning: Remove any cloth filter. Place the sponge filter over the motor unit's filter cage. Do not use the cloth filter for wet cleaning.

Image 3.2: Washable cloth filter for dry pickup and sponge filter for wet pickup. The image also illustrates the buoy technology that stops water suction when the tank is full.

3.5 Attaching the Hose and Accessories

1. Insert the hose pipe into the air suction port on the front of the container until it is firmly seated.
2. Attach the desired extension pipes to the handle grip of the hose.
3. Connect the appropriate cleaning brush or nozzle (e.g., Dry & Wet Squeezing Brush, 2-in-1 Crevice Nozzle, Small Round Brush) to the end of the extension pipes.

Image 3.3: The vacuum cleaner assembled with its 1.8m flexible hose, 3x 0.30m extension tubes, and 4.0m power cord, providing over 7.0m cleaning range.

4. Operating Instructions

The INALSA Homeasy WD10 offers wet, dry, and blower functions.

4.1 Dry Vacuuming

1. Ensure the cloth filter is correctly installed.
2. Connect the desired dry cleaning attachment (e.g., Dry & Wet Squeezing Brush for floors, Crevice Nozzle for tight spaces).
3. Plug the power cord into a suitable electrical outlet.
4. Press the On/Off switch to start the vacuum cleaner.
5. Guide the attachment over the surface to be cleaned.
6. After use, press the On/Off switch to turn off the appliance and unplug it.

4.2 Wet Vacuuming

1. Important: Remove the cloth filter and install the sponge filter for wet cleaning.
2. Connect the Dry & Wet Squeezing Brush or other suitable wet cleaning attachment.
3. Plug the power cord into a suitable electrical outlet.
4. Press the On/Off switch to start the vacuum cleaner.
5. Guide the attachment over the wet surface to pick up liquids.
6. The built-in Safe Buoy technology will automatically stop suction when the liquid capacity reaches its maximum point, protecting the motor.
7. After use, press the On/Off switch to turn off the appliance and unplug it. Empty the tank immediately after wet use.

4.3 Blower Function

1. Important: Ensure no filter is installed in the vacuum cleaner for effective blowing results.
2. Remove the hose from the air suction port.
3. Insert the hose pipe into the blower port located on the motor unit.
4. Plug the power cord into a suitable electrical outlet.
5. Press the On/Off switch to activate the blower function.
6. Direct the hose towards the area you wish to blow clean (e.g., dislodge dust, dry surfaces).
7. After use, press the On/Off switch to turn off the appliance and unplug it.

Image 4.1: Wide applications including carpet cleaning, blowing leaves, dry cleaning, sofa surface cleaning, wet cleaning, and small corner cleaning.

5. Maintenance and Cleaning

Regular maintenance ensures optimal performance and extends the life of your vacuum cleaner.

5.1 Emptying the Tank

1. Ensure the vacuum cleaner is turned off and unplugged.
2. Release the latches on the sides of the container and lift off the motor unit.
3. Carefully empty the collected dust or liquid from the 10-liter tank.
4. Clean the inside of the tank with a damp cloth if necessary and allow it to dry completely before reassembling.

5.2 Cleaning Filters

Clean filters regularly to maintain suction power.

• Cloth Filter: For dry use, remove the cloth filter and shake off accumulated dust. It can be gently hand-washed with mild soap and water. Ensure it is completely dry before reinstallation.
• Sponge Filter: For wet use, remove the sponge filter and rinse it under running water. Squeeze out excess water and allow it to air dry completely before storage or next use.

5.3 Cleaning Accessories

Wipe down the hose, extension pipes, and nozzles with a damp cloth. Ensure they are free from blockages.

6. Troubleshooting

If you encounter issues with your vacuum cleaner, refer to the following common problems and solutions:

7. Specifications

8. Warranty and Support

8.1 Warranty Information

This INALSA Homeasy WD10 Wet and Dry Vacuum Cleaner comes with a 1-year manufacturer warranty from the date of purchase. Please retain your purchase receipt for warranty claims. The warranty covers manufacturing defects under normal use conditions.

8.2 Customer Support

For any queries, service requests, or technical assistance, please contact the manufacturer:

• Manufacturer: Tuareg Marketing Pvt Ltd
• Address: 154, Bhalswa, Delhi- 110033

Please refer to the warranty card included with your product for detailed terms and conditions and additional contact information.