upHere 120mm RGB Series Case Fan Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your upHere 120mm RGB Series Case Fan. Designed for high airflow and quiet operation, these fans enhance your PC's cooling performance and aesthetic appeal. Please read this manual thoroughly before installation and use to ensure proper functionality and longevity of your product.

Key Features

High Airflow: 120mm fan optimized for efficient air movement and high-volume cooling.
Quiet Operation: Equipped with rubber pads and a hydraulic bearing to minimize operating noise and improve efficiency.
Vibrant RGB Lighting: 6-pin interface provides safe and reliable power output for bright and colorful RGB lighting effects.
Versatile Installation: Supports two-way installation for either exhausting warm air or drawing cool air into the PC case.

upHere 120mm RGB fan with airflow arrows — Image: Diagram illustrating the high airflow capability of the upHere 120mm RGB fan, showing air moving through the fan blades and out of the case.

Multiple upHere RGB fans displaying various colors — Image: A grid of nine upHere RGB fans, each showcasing a different static color or multi-color effect, highlighting the customizable lighting options.

Setup and Installation

Follow these steps to properly install your upHere 120mm RGB Series Case Fans:

Prepare Your PC Case: Ensure your PC is powered off and unplugged. Open your PC case to access the fan mounting locations.
Mount the Fans: Position the 120mm fans in your desired locations (e.g., front, top, rear, bottom). Use the included screws to secure each fan. Ensure the fan's airflow direction (indicated by arrows on the fan frame) matches your cooling strategy (intake or exhaust).
Connect to the Fan Hub: Connect each 6-pin fan cable to an available port on the upHere fan hub. The fan hub typically supports multiple fans.
Power the Fan Hub: Connect the fan hub to your power supply unit (PSU) using the provided SATA power connector.
Cable Management: Route all cables neatly to avoid obstructing airflow and for a clean build.

Diagram showing upHere RGB fan installation with hub and power supply — Image: An installation guide diagram for upHere RGB fans, showing five fans connected to a central upHere hub, which is then connected to a power supply via a SATA connector.

Note: The fan hub included with your upHere fans is essential for controlling the RGB lighting and fan speeds. It connects directly to your PSU via SATA power and does not require a motherboard RGB header for basic functionality.

Operating Instructions

Your upHere RGB fans are controlled via the included remote control, which allows for customization of lighting effects and fan speeds.

Remote Control Functions:

Power On/Off: Turn the fan lighting on or off.
Mode Selection: Cycle through various RGB lighting modes (static colors, breathing, rainbow, etc.).
Color Adjustment: Select specific static colors or adjust color patterns.
Brightness Control: Increase or decrease the intensity of the RGB lighting.
Fan Speed Adjustment: Adjust the fan rotation speed to balance cooling performance and noise levels.

Refer to the remote control's specific buttons for each function. The fan hub does not typically connect to motherboard RGB headers, so all controls are managed through the remote.

Video: A short video demonstrating the various RGB lighting effects and colors of the upHere case fans installed in a PC build.

Video: A user-submitted video showcasing the upHere RGB fans in operation, highlighting their visual appeal and quiet performance.

Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your upHere case fans.

Dust Cleaning: Periodically clean dust from the fan blades and frames using compressed air or a soft brush. Ensure the PC is powered off and unplugged before cleaning.
Inspect Cables: Check all fan and power cables for secure connections and any signs of wear or damage.
Bearing Noise: If you notice increased noise from a fan, it may indicate a worn bearing. While these fans use hydraulic bearings designed for longevity, excessive noise might require replacement.

Troubleshooting

Problem	Possible Cause	Solution
Fans not spinning	Loose power connection to fan hub. Fan cable not properly connected to hub. Faulty fan or hub.	Ensure SATA power cable is securely connected to PSU and hub. Verify all 6-pin fan cables are firmly seated in the hub. Test individual fans if possible; contact support if faulty.
RGB lights not working	Remote control battery dead. Incorrect mode selected on remote. Loose connection to fan hub.	Replace remote control battery. Cycle through modes using the remote. Check 6-pin fan cable connections to the hub.
Excessive fan noise	Dust accumulation on blades. Loose mounting screws. Fan bearing wear.	Clean fan blades. Tighten mounting screws. If noise persists, consider fan replacement.

Product Specifications

Attribute	Detail
Product Dimensions	4.72"L x 0.98"W x 4.72"H (120mm x 25mm x 120mm)
Brand	upHere
Power Connector Type	SATA (for fan hub)
Voltage	12 Volts
Wattage	1.1 watts
Cooling Method	Air
Compatible Devices	Desktop PC Cases
Noise Level	25 Decibels
Material	Plastic
Maximum Rotational Speed	2000 RPM
Air Flow Capacity	38 Cubic Feet Per Minute (CFM)
Item Model Number	ZC RGB12305-01 US

Warranty and Support

For warranty information and technical support, please refer to the official upHere website or contact your retailer. Keep your proof of purchase for warranty claims.

Contact Information:

Manufacturer: upHere
Website: Visit the upHere Store on Amazon (for general product information)
For specific support, please check the packaging or included documentation for direct contact details.

	NZXT H5 Flow Compact Mid-Tower Airflow Case Manual This document provides a comprehensive guide to the NZXT H5 Flow, a compact mid-tower airflow PC case. It includes an exploded view of components, clearances and specifications, accessory box contents, cable connections, buttons and I/O details, panel removal instructions, cable management system overview, and installation guides for motherboards, storage, expansion cards, power supplies, fans, and radiators. The manual also covers downloading NZXT CAM software and the NZXT Global Warranty Policy.
	NZXT H3 Flow Micro-ATX Airflow Case: Specifications, Installation, and Warranty A comprehensive guide for the NZXT H3 Flow Micro-ATX Airflow PC case, covering its features, technical specifications, component installation procedures, cable management, and the global warranty policy.
	NZXT H9 Flow Dual-Chamber Mid-Tower Airflow Case User Manual Comprehensive user manual for the NZXT H9 Flow dual-chamber mid-tower ATX computer case, detailing product information, components, ports, installation guides, and warranty policy.
	NZXT H9 Flow CM-H91FB-01 PC Case Installation Guide and Specifications Comprehensive installation guide, specifications, and warranty information for the NZXT H9 Flow Dual-Chamber Mid-Tower Airflow PC Case (Model CM-H91FB-01).
	SAVIO FAN-01 / FAN-01 WHITE 4x ARGB 120mm Fan Kit User Manual User manual for the SAVIO FAN-01 / FAN-01 WHITE kit, featuring four 120mm ARGB computer fans, a controller, and a remote for customizable lighting and fan speed. Includes technical specifications, installation guide, and safety information.
	Thermaltake View 390 TG Mid Tower PC Case User Manual This user manual provides detailed specifications, installation guides, and clearance information for the Thermaltake View 390 TG Mid Tower PC Case. It covers component installation, cooling options, and I/O connections for building a custom PC.

upHere ZC RGB12305-01 US