Important Safety Information
Please read this entire manual carefully before installing or operating your Heatstar HSSVFBF30NGBT natural gas heater. Failure to follow these instructions could result in property damage, personal injury, or death. Keep this manual for future reference.
- This appliance is for indoor use only.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- Proper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information, consult a qualified installer, service agency, or the gas supplier.
- This is a vent-free appliance. It uses air from the room in which it is installed. Provide adequate combustion and ventilation air.
- Carbon Monoxide Hazard: This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in a living area without proper ventilation.
Package Contents
Verify that all components are present before beginning installation:
- Heatstar HSSVFBF30NGBT Heater Unit
- Blower Assembly
- Mounting Hardware (screws, anchors)
- Instruction Manual (this document)
- Base Feet (for freestanding option)
This image displays the front of the Heatstar HSSVFBF30NGBT natural gas heater. The unit is light-colored, likely off-white or beige, with a black protective grate covering the burner area. Through the grate, a distinct blue flame is visible, indicating the 'blue flame' heating technology. Ventilation slats are present on the top and bottom of the unit, and two small feet are visible at the bottom for freestanding placement, though it is also wall-mountable.
Setup and Installation
Location Requirements
- Ensure adequate clearances from combustible materials as specified in the installation instructions.
- Select a location with proper ventilation and air circulation.
- Do not install in bathrooms or bedrooms unless local codes permit.
Wall Mounting
- Identify a suitable wall location, ensuring it can support the heater's weight.
- Mark the mounting screw locations using the template provided (if applicable) or by measuring the heater's mounting points.
- Drill pilot holes and insert wall anchors if necessary.
- Securely attach the heater to the wall using the provided mounting screws.
Gas Connection
- All gas connections must be performed by a qualified professional in accordance with local codes.
- Ensure the gas supply is turned off before making any connections.
- Connect the natural gas supply line to the heater's gas inlet using appropriate fittings and pipe sealant.
- Check all connections for leaks using a non-corrosive leak detection solution.
Blower Installation
- Locate the blower mounting area on the heater (typically at the top or rear).
- Attach the blower assembly according to the specific instructions provided with the blower kit.
- Connect the blower's power cord to a standard electrical outlet.
Operating Instructions
Lighting the Pilot
- Ensure the gas supply valve is open.
- Turn the control knob to the 'PILOT' position.
- Press and hold the control knob in.
- While holding the knob, press the igniter button repeatedly until the pilot flame lights.
- Continue to hold the control knob in for approximately 30-60 seconds after the pilot lights to allow the thermocouple to heat up.
- Release the control knob. If the pilot goes out, repeat the process.
Operating the Heater
- Once the pilot is lit, turn the control knob to the desired heat setting (e.g., 'LOW', 'MED', 'HIGH' or a specific temperature on the thermostat).
- The main burner will ignite.
- The integrated blower will activate automatically when the heater reaches a certain temperature, circulating warm air.
Shutting Down
- To turn off the main burner, turn the control knob to the 'OFF' position. The pilot light will also extinguish.
- For extended periods of non-use, turn off the main gas supply valve to the heater.
Maintenance
Cleaning
- Exterior: Clean the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Burner/Pilot Area: Periodically inspect the burner and pilot areas for dust, lint, or debris. Use a vacuum cleaner with a soft brush attachment to gently remove any accumulations. Ensure the heater is cool and the gas supply is off before cleaning.
Annual Inspection
It is recommended to have the heater inspected annually by a qualified service technician to ensure proper operation and safety.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Pilot will not light | No gas supply; Air in gas line; Faulty igniter; Pilot orifice clogged | Check gas valve; Bleed air from line; Contact service; Clean pilot orifice |
| Pilot lights but will not stay lit | Control knob not held long enough; Loose thermocouple connection; Faulty thermocouple | Hold knob longer; Tighten connection; Contact service |
| Main burner will not light | Pilot not lit; Thermostat set too low; Main burner orifice clogged | Light pilot; Adjust thermostat; Contact service |
| Unusual odor | Gas leak; New unit burn-off; Dust on burner | Immediately turn off gas and ventilate. Do not operate. Contact gas supplier. Normal for new units; Clean burner area. |
Specifications
| Feature | Specification |
|---|---|
| Model Number | HSSVFBF30NGBT |
| Heat Output | 30,000 BTU |
| Fuel Type | Natural Gas |
| Burner Type | Blue Flame Radiant |
| Heating Coverage | Up to 300 sq ft |
| Control Type | Manual Thermostat |
| Mounting Type | Wall Mount (with optional base for freestanding) |
| Indoor/Outdoor Usage | Indoor Only |
| UPC | 720968960962 |
Warranty and Support
For warranty information and customer support, please refer to the warranty card included with your product or contact Heatstar By Enerco customer service directly. Keep your purchase receipt as proof of purchase.
Heatstar By Enerco Customer Service: Please visit the official Heatstar website or refer to your product packaging for current contact information.