1. Introduction
Welcome to the user manual for your Empava 59-Inch Corner Whirlpool Bathtub. This document provides important instructions for the safe installation, operation, and maintenance of your new bathtub. Please read this manual thoroughly before installation and use, and retain it for future reference.
This Empava whirlpool bathtub is designed to provide a relaxing hydromassage experience with integrated heating and chromatherapy features. Proper installation and care are essential for optimal performance and longevity.
2. Safety Information
WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Electrical Safety: The bathtub requires a 110 Volt AC power supply. It must be connected to two separate 15A Dedicated GFCI (Ground Fault Circuit Interrupter) circuits. All electrical connections must be performed by a qualified electrician in accordance with local and national electrical codes. The motor is UL Certified, and the entire unit is ETL Certified, ensuring it meets safety and performance standards.
- Water Temperature: The inline heater is designed to maintain the water temperature between 96.8°F (36°C) and 104°F (40°C). It is not intended to heat cold water to a desired temperature. Always fill the tub with hot water.
- Water Level: Ensure the water level is above the jets before activating the whirlpool function. The jet protection system will prevent operation if the water level is insufficient.
- Weight Capacity: The bathtub has a water capacity of 91 gallons. Be aware of the combined weight of water and occupants. Ensure the floor structure can support this weight.
- Chemicals: Use only approved bath additives. Avoid abrasive cleaners or harsh chemicals that may damage the acrylic surface or internal components.
3. Product Overview
The Empava 59-Inch Corner Whirlpool Bathtub is designed for two persons, featuring a powerful hydromassage system, chromatherapy lighting, and an inline heater for extended comfort.
Key Features:
- 750W Whirlpool System: Equipped with 10 strategically placed water jets driven by a 1.0 HP UL Certified motor for effective hydromassage.
- 2-Person Capacity: Spacious design with a 125° recline angle and two pillows for comfortable seating.
- Chromatherapy Lighting: Integrated LED lights provide various color options to enhance relaxation.
- Inline Heater: Maintains desired water temperature during use (96.8°F - 104°F).
- Durable Construction: Made from 100% acrylic and reinforced with fiberglass resin, supported by a 304 stainless steel frame.
- Integrated Controls: User-friendly LED control panel for managing all functions.
Components:
- Water Jets (10 pcs)
- Headrest Pillows (2 pcs)
- LED Control Panel
- Inline Heater
- Waterfall Faucet
- Pull-out Handshower
- Hot/Cold Water Outlet Transfers
- Drainer and Overflow
Figure 3.1: Empava 59-Inch Corner Whirlpool Bathtub with blue chromatherapy lighting.
Figure 3.2: Key features of the Empava 2-Person Whirlpool Tub.
Figure 3.3: Bathtub components and control panel functions.
4. Specifications
| Feature | Specification |
|---|---|
| Brand | Empava |
| Model Number | 59JT319 |
| Material | Acrylic |
| Product Dimensions | 59"L x 59"W x 28"H |
| Item Weight | 150 Pounds |
| Installation Type | Alcove / Corner |
| Capacity | 91 Gallons |
| Shape | Semi-Circular |
| Voltage | 110 Volts |
| Power Source | AC |
| Special Features | Whirlpool, Heater, Chromatherapy |
| Certifications | ETL Certified, UL Certified Motor |
Figure 4.1: Detailed Dimensions and Layout.
Figure 4.2: Bathtub Capacity and Internal Measurements.
5. Installation
Professional installation is highly recommended for this product to ensure proper function and safety. Ensure all local plumbing and electrical codes are followed.
Pre-Installation Checks:
- Inspect the bathtub for any damage prior to installation.
- Verify all connections (plumbing and electrical) are secure. Some connections may require tightening during installation.
- Ensure the installation area has adequate floor support for the filled bathtub and occupants.
Installation Requirements:
- Drainage Hole: A drainage hole with a minimum diameter of 1.97 inches (50mm) is required.
- Electrical Connection: The power must be connected to the terminal box. This requires two separate 15A Dedicated GFCI Circuits. The voltage is 110V, and the power consumption is 750W.
- Water Pipes: 1/2-inch hot and cold water pipes are required.
- Drain Pipe Length: The drain pipe length is 31 inches (800mm).
- Shower Head Hose Length: The shower head hose length is 59 inches (1500mm).
Figure 5.1: Installation Diagram with Key Measurements.
Figure 5.2: Underside Plumbing and Electrical Connections.
6. Operating Instructions
6.1 Filling the Bathtub
- Ensure the drain is closed.
- Turn on the hot and cold water faucets to fill the bathtub.
- Fill the tub until the water level is above the highest jets. Do not overfill.
6.2 Using the Control Panel
The LED control panel allows you to manage all bathtub functions. Refer to the specific icons for each feature:
- Mood Light: Activates the chromatherapy lighting.
- Hydro Massage + Waterfall: Turns on the water jets and waterfall feature.
- Inline Heater: Engages the heater to maintain water temperature.
- Air Bubble: (If available on your model) Activates the air bubble massage.
6.3 Whirlpool Hydromassage
- Once the tub is filled to the appropriate level, press the 'Hydro Massage' button on the control panel.
- Adjusting Jet Intensity: Rotate the hydro massage strength control (located on the jet) clockwise to decrease water intensity or counter-clockwise to increase it.
- Adjusting Jet Direction: Swivel the individual jets to direct the water streams to specific areas for targeted massage.
Figure 6.1: Jet Adjustment for Intensity and Direction.
6.4 Inline Heater Operation
- The inline heater is activated via the control panel.
- It will maintain the water temperature within the specified range (96.8°F - 104°F).
- Note: The heater is designed for temperature maintenance, not for initial heating of cold water. Always start with hot water.
Figure 6.2: Heater Functionality for Temperature Maintenance.
6.5 Chromatherapy Lighting
- Press the 'Mood Light' button on the control panel to cycle through various color options or set a preferred color.
Figure 6.3: Chromatherapy Lighting in Operation.
7. Maintenance
7.1 Cleaning the Bathtub
- After each use, drain the tub completely.
- Wipe down the acrylic surface with a soft cloth and a non-abrasive, mild bathroom cleaner. Avoid harsh chemicals, abrasive pads, or solvents, as these can damage the acrylic finish.
- For stubborn stains, consult the cleaner manufacturer's instructions for use on acrylic surfaces.
7.2 Jet and Plumbing System Cleaning
- Periodically, fill the tub with warm water and add a small amount of a non-foaming jet cleaner or a cup of white vinegar.
- Run the whirlpool system for 10-15 minutes to circulate the cleaning solution through the jets and plumbing.
- Drain the tub, then refill with clean water and run the jets for a few minutes to rinse the system.
8. Troubleshooting
This section addresses common issues you might encounter with your Empava whirlpool bathtub.
| Problem | Possible Cause | Solution |
|---|---|---|
| Whirlpool jets do not activate. | Insufficient water level; Power supply issue; Control panel malfunction. | Ensure water level is above jets. Check GFCI breakers. Verify power connection. Consult a qualified technician if problem persists. |
| Heater not maintaining temperature. | Heater not activated; Starting with cold water; Heater malfunction. | Activate heater via control panel. Always fill with hot water. Contact support if heater is faulty. |
| Water drains slowly. | Drain obstruction; Improper drain installation. | Check drain for debris. Ensure drain pipe is correctly installed and free of kinks. |
| Control panel unresponsive. | Power supply issue; Loose connections; Panel malfunction. | Check GFCI breakers. Ensure all electrical connections are secure. If necessary, consult a qualified technician. |
| Unusual noises during operation. | Air in pump; Loose components; Motor issue. | Ensure water level is sufficient. Check for loose plumbing connections. If noise persists, contact support. |
9. Warranty and Support
This Empava whirlpool bathtub comes with a 3-year manufacturer's warranty. Please retain your proof of purchase for warranty claims.
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Empava customer support. You can find more information and contact details by visiting the official Empava Store.
Empava Store: Visit the Empava Store on Amazon
