Introduction
The step2bed XL is a robust and adjustable bedside step stool designed to provide assistance for individuals requiring support when getting in and out of bed. It features LED light-guided rails for enhanced visibility and safety, and is constructed from stainless steel to ensure durability and stability. This manual provides essential information for assembly, setup, operation, and maintenance of your step2bed XL.
Safety Information
- Always ensure all bolts and fasteners are securely tightened before each use.
- Verify that the step stool is stable and does not wobble.
- Do not exceed the maximum weight capacity of 800 lbs.
- Ensure the motion-activated LED light is functioning correctly for nighttime visibility.
- Use the provided self-adhering straps to secure the step stool to the bed frame to prevent movement.
- Keep the step surface clean and dry to prevent slips.
- Consult a healthcare professional if you have specific mobility concerns or conditions.
Package Contents
Before assembly, ensure all components are present:
- Main step platform
- Tall grab bar (with foam padding)
- Short grab bar
- Crossbar
- Adjustable legs (4)
- Motion-activated LED light
- Self-adhering Velcro straps (2)
- Assembly hardware (bolts, nuts, washers)
- Instruction manual
Assembly Instructions
Follow these steps to assemble your step2bed XL. It is recommended to have a second person assist with assembly.
- Insert the tall and short grab bars into the designated holes on the main step platform.
- Attach the crossbar between the two grab bars, ensuring proper alignment. Secure with bolts and tighten.
- Insert the four adjustable legs into the bottom of the main step platform.
- Turn the step2bed XL on its side to access the leg adjustments.
- Adjust each leg to the desired height by pressing the pin and sliding the inner tube. Ensure all four legs are set to the same height for stability.
- Secure the motion-activated LED light to the underside of the step platform using the provided adhesive or brackets, ensuring the sensor faces outwards.
- Stand the step2bed XL upright and ensure all connections are secure.
Setup and Adjustment
The step2bed XL offers adjustable height settings and can be secured to your bed for added stability.
Height Adjustment
The step height can be adjusted from 2.5 inches to 7.5 inches. To adjust, press the spring-loaded pin on each leg and slide the inner tube to the desired height. Ensure all four legs are adjusted to the same level to maintain stability and prevent wobbling.
Securing to Bed
Use the two self-adhering Velcro straps to attach the step2bed XL to your bed frame. Wrap the straps around the bed frame and the step stool's frame, tightening them securely. This prevents the step stool from shifting during use.
Operating Instructions
The step2bed XL is designed to facilitate safe and independent bed transfers.
Getting Into Bed
- Approach the step2bed XL, turning sideways towards the bed.
- Place both hands on the tall grab bar for support.
- Step onto the platform with one foot, then bring the other foot up.
- With hands still on the tall grab bar, sit down on the edge of the bed.
- Lay down into a resting position, lifting your legs over the short rail and into bed.
Getting Out of Bed
- Reach for the closest arm of the tall grab bar.
- Use the rail to lift your shoulders off the bed while swinging your legs over the short rail and placing your feet on the step platform.
- Take 15-30 seconds while sitting up to regain your composure.
- When ready, use one hand on the tall grab bar or two hands (one on the tall rail, one on the short rail) and stand up.
- While keeping one hand on the tall grab bar, slowly step off the step2bed onto the floor.
Maintenance
- Cleaning: Wipe down the stainless steel frame and step platform with a damp cloth and mild detergent. Avoid abrasive cleaners that could damage the finish.
- Inspection: Regularly inspect all bolts, nuts, and connections to ensure they are tight. Check the rubber feet for wear and tear.
- LED Light: Ensure the motion-activated LED light is clean and unobstructed. Replace batteries as needed.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Step stool wobbles | Uneven leg adjustment; loose bolts; not secured to bed. | Ensure all legs are at the same height. Tighten all assembly bolts. Use Velcro straps to secure to bed frame. |
| LED light not working | Dead batteries; sensor obstructed; light switch off. | Replace batteries. Clear any obstructions from the sensor. Check if the light has an on/off switch and ensure it is in the 'on' position. |
| Difficulty getting in/out of bed | Incorrect step height; improper technique. | Adjust step height to a comfortable level. Review operating instructions and practice transfers. |
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 18"D x 32"W x 32"H (Maximum Height) |
| Material | Stainless Steel |
| Color | White |
| Special Features | Adjustable Height, Durable, Extra Wide, Portable, Motion-Activated LED Light |
| Adjustable Step Height | 2.5" - 7.5" |
| Weight Limit | 800 Pounds |
| Item Weight | 23.7 pounds (10.8 Kilograms) |
| Assembly Required | Yes |
| Number of Steps | 1 |
| UPC | 860250001031 |
Warranty Information
The step2bed XL comes with a 30-day warranty on our elderly assistance products. This warranty covers manufacturing defects and ensures the product meets quality standards. For warranty claims or further details, please contact customer support.
Support
For any questions, concerns, or assistance with your step2bed XL, please refer to the contact information provided with your purchase or visit the official step2bed website. Our customer service team is available to help with assembly, troubleshooting, and general inquiries.
