Seismic Audio Tower1 Powered Portable Column Array PA System Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your Seismic Audio Tower1 Powered Portable Column Array PA System. Please read this manual thoroughly before use and retain it for future reference.

The Tower1 system is designed for portable sound reinforcement, featuring a 10-inch subwoofer and a column array speaker with four 3-inch speakers, an integrated mixer, and Bluetooth connectivity.

2. Safety Information

Always observe the following safety precautions:

• Do not expose the unit to rain or moisture.
• Do not open the casing; refer all servicing to qualified personnel.
• Ensure proper ventilation to prevent overheating.
• Use only the specified power supply.
• Avoid placing the unit on unstable surfaces.
• Disconnect power before cleaning or maintenance.
• This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning).

3. Package Contents

Verify that all components are present:

• 1x Active 10" Subwoofer Cabinet
• 1x Column Speaker (with four 3-inch speakers)
• 1x Power Cable
• 1x Instruction Manual (this document)

4. Setup Instructions

Follow these steps to set up your Tower1 PA System:

1. Unpack Components: Carefully remove all items from the packaging.
2. Position the Subwoofer: Place the active 10-inch subwoofer on a stable, flat surface. Ensure adequate space for ventilation around the unit.
3. Attach the Column Speaker: Gently insert the column speaker into the designated multi-pin connector on top of the subwoofer cabinet. Ensure it is securely seated.
4. Connect Power: Connect the power cable to the AC input on the rear of the subwoofer, then plug it into a suitable power outlet. Ensure the power switch is in the OFF position before connecting.

Figure 4.1: Assembled Tower1 PA System. This image shows the subwoofer base with the column array speaker securely attached on top.

Figure 4.2: Tower1 PA System with dimensions. The image illustrates the overall dimensions of the assembled unit, including height, width, and depth.

5. Operating Instructions

5.1 Powering On/Off

• To power on, ensure all volume controls are at their minimum, then flip the power switch on the rear panel to the ON position.
• To power off, turn all volume controls to minimum, then flip the power switch to the OFF position.

5.2 Mixer Controls

The Tower1 features a built-in mixer with various input options and controls:

Figure 5.1: Top view of the Tower1 mixer controls. This image displays the various knobs and faders for adjusting input levels and master volume.

• CH1-CH4 Level: Adjusts the input level for each channel.
• Line/MIC Switch: Selects input sensitivity for microphone or line-level sources.
• Master Level: Controls the overall output volume of the system.
• Hi/Low EQ: Adjusts the high and low frequencies for tone shaping.
• Effects Delay: Controls the delay effect for inputs.

5.3 Input Connections

The system offers multiple input options:

Figure 5.2: Rear view of the Tower1 input connections. This image shows the various ports for connecting audio sources.

• Mic/Line (Combo Jack): For microphones or line-level instruments (XLR or 1/4" TRS).
• 3.5mm Jack: For connecting portable audio devices.
• RCA (Input): For connecting stereo audio sources.
• RCA (AUX Out): For sending the mixed signal to another device.

5.4 Bluetooth Connectivity

The Tower1 features built-in Bluetooth 4.0 for wireless audio streaming:

1. Activate Bluetooth on your audio device (smartphone, tablet, etc.).
2. Select "Tower1" from the list of available devices.
3. Once paired, audio from your device will play through the PA system.
4. The system supports stereo wireless connectivity.

5.5 MP3 Player

The integrated MP3 player allows playback from USB drives. Insert a USB drive with MP3 files into the USB port on the mixer panel. Use the player controls to navigate and play tracks.

6. Maintenance

• Cleaning: Use a soft, dry cloth to clean the exterior surfaces. Do not use abrasive cleaners or solvents.
• Storage: When not in use, store the system in a dry, cool environment, protected from dust and extreme temperatures.
• Ventilation: Ensure that the cooling convection vents are not obstructed during operation.

7. Troubleshooting

8. Specifications

9. Warranty Information

For information regarding product warranty, please refer to the official Seismic Audio website or contact customer support directly. Protection plans may be available for purchase separately.

10. Customer Support

If you encounter any issues or have questions not covered in this manual, please contact Seismic Audio customer support. Visit the Seismic Audio Store for contact details or further assistance.