Fortnite Hasbro Victory Royale Series Midas Rex Action Figure Instruction Manual

Introduction

This manual provides instructions for the assembly, operation, and care of your Fortnite Hasbro Victory Royale Series Midas Rex collectible action figure. Please read these instructions carefully to ensure proper handling and to maximize the enjoyment of your product.

Setup and Assembly

The Midas Rex action figure comes with several accessories. Follow these steps for initial setup:

1. Unboxing: Carefully remove the Midas Rex figure and all accessories from the packaging. Ensure all components listed in the "What's in the Box" section are present.
2. Attaching the Cape Back Bling: The Midas Crest Back Bling (cape) can be attached to the figure's back. Locate the peg on the back bling and align it with the corresponding hole on the figure's back. Gently push until it is securely in place.
3. Interchanging Heads: The figure includes a standard head and an alternate helmeted head.
   • To remove the current head, gently pull it upwards from the neck joint.
   • To attach a new head, align the neck peg with the hole in the head and gently push down until it is secure.
4. Weapon Accessories: The Kingmaker Harvesting Tool (sword) can be held in either of the figure's hands. The pistols on the figure's hips are removable from their holsters.

Image: Midas Rex figure with all accessories, including the alternate helmet head, cape, and sword.

Image: Front view of the Midas Rex action figure, fully assembled with the standard head.

Operating and Articulation

The Midas Rex figure features over 20 points of articulation, allowing for a wide range of poses. Handle the figure with care when adjusting its pose.

• Head: Ball joint for rotation and tilt.
• Shoulders: Ball joints for rotation and outward movement.
• Biceps: Swivel joint.
• Elbows: Double-pinless hinge joints for deep bending.
• Wrists: Swivel and hinge joints.
• Torso: Abdominal crunch and waist swivel for upper body movement.
• Hips: Ball joints for forward, backward, and outward leg movement.
• Thighs: Swivel joint.
• Knees: Double-pinless hinge joints for deep bending.
• Ankles: Hinge and rocker joints for stability and posing.

When posing, apply gentle, even pressure to avoid stressing the joints. Avoid forcing joints beyond their natural range of motion.

Maintenance and Care

To maintain the condition of your Midas Rex action figure:

• Cleaning: Use a soft, dry cloth to gently wipe away dust. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying. Avoid harsh chemicals or abrasive cleaners.
• Storage: Store the figure away from direct sunlight, extreme temperatures, and high humidity to prevent discoloration or material degradation. Keep accessories in a safe place to avoid loss.
• Handling: Avoid dropping the figure or applying excessive force to its parts, especially small accessories and articulated joints.

Troubleshooting

If you encounter any issues with your Midas Rex action figure, consider the following:

• Loose Joints: If a joint feels too loose, it may be possible to tighten it using a small amount of clear nail polish or a specialized joint-tightening fluid. Apply sparingly and allow to dry completely.
• Stiff Joints: If a joint is too stiff, gently warm the area with a hairdryer on a low setting for a few seconds to make the plastic more pliable. Then, carefully work the joint to loosen it. Do not overheat.
• Missing Accessories: Double-check the packaging and surrounding area. If an accessory is genuinely missing upon purchase, contact customer support.

Specifications

Safety Information: WARNING: CHOKING HAZARD – Small parts may be generated. Not for children under 3 years.

Warranty and Support

For information regarding product warranty or customer support, please refer to the official Hasbro website or contact their customer service department directly. Keep your proof of purchase for any warranty claims.

Official Hasbro Website: www.hasbro.com